[Asterisk-Users] Wildcard TE110p initial setup

[Goolsby, Daniel S (Daniel)]

I'm not 'overly' new to asterisk, but I am very new to the Digium card / Telco aspect of it.  

 

I was able to get a TE110p card, installed.. and hooked a t1 up to it.  I'm using zttool to just look at 'some' output.  Here is what it looks like when I just load it up:

 

Current Alarms:     No alarms.                          â     â

   â     â    Sync Source:        Internally clocked                  â  â  â

   â     â    IRQ Misses:               0                             â  â  â

   â     â    Bipolar Viol:             0                             â  â  â

   â     â    Tx/Rx Levels:         0/  0                             â  â  â

   â     â    Total/Conf/Act:      24/ 24/  0                         â  â  â

   â     â                 111111111122222                ââââââââ    â  â  â

   â     â        123456789012345678901234                â Back â    â  â  â

   â     â    TxA 000000000000000000000000                ââââââââ    â  â  â

   â     â    TxB 000000000000000000000000                            â  â  â

   â     â    TxC 000000000000000000000000                            â  #  â

   â     â    TxD 000000000000000000000000                            â     â

   â     â                                                ââââââââ    â     â

   â     â    RxA 000000000000000000000000                â Loop â    â     â

   â     â    RxB 000000000000000000000000                ââââââââ    â     â

   â     â    RxC 000000000000000000000000                            â     â

   â     â    RxD 000000000000000000000000                            â

 

If I make a call to one of the phone numbers in my block, the zttool output goes to this:

 

â    Current Alarms:     No alarms.                          â     â

   â     â    Sync Source:        Internally clocked                  â  â  â

   â     â    IRQ Misses:               0                             â  â  â

   â     â    Bipolar Viol:             0                             â  â  â

   â     â    Tx/Rx Levels:         0/  0                             â  â  â

   â     â    Total/Conf/Act:      24/ 24/  1                         â  â  â

   â     â                 111111111122222                ââââââââ    â  â  â

   â     â        123456789012345678901234                â Back â    â  â  â

   â     â    TxA 000000000000000000000000                ââââââââ    â  â  â

   â     â    TxB 000000000000000000000000                            â  â  â

   â     â    TxC 000000000000000000000000                            â  #  â

   â     â    TxD 000000000000000000000000                            â     â

   â     â                                                ââââââââ    â     â

   â     â    RxA 100000000000000000000000                â Loop â    â     â

   â     â    RxB 100000000000000000000000                ââââââââ    â     â

   â     â    RxC 000000000000000000000000                            â     â

   â     â    RxD 000000000000000000000000                            â

 

Channel 1's RxA and RxB goes to 1, while nothing else happens.  I'm running somewhat of a latest build, with AMP installed.  I see that it's configured that any incoming call is in the 'from-pstn', but I have yet to get a busy signal, or any response from the card.  

 

What I would like to know is it my card, software, or t1?  I'll give up just about any information asked for, if someone could help me.

 

Daniel

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050506/6a7e1a54/attachment.htm