[Asterisk-Users] Problem with TE405P and Slackware 10.0

[pixer]

Hi to all,
I have a problem with this wildcard and one E1 line.

The server is a Asus P4P800S with the 865PE chipset, and 512MB RAM. The
kernel version is 2.4.26.

I have donwload and build the latest CVS version of zaptel, libpri and
asterisk following the ufficial instructions of digium.
I have set up my server in this way:


zaptel.conf

loadzone=it
defaultzone=it

span=1,1,0,ccs,hdb3,crc4,yellow

bchan=1-15,17-31
dchan=16


zapata.conf

switchtype = EuroISDN
signalling = pri_cpe
pridialplan = unknown
context = incoming
group = 2
channel => 1-15,17-31


root at asterisk:/usr/src# rmmod wct4xxp zaptel
root at asterisk:/usr/src# modprobe zaptel
root at asterisk:/usr/src# modprobe wct4xxp

root at asterisk:/usr/src# ztcfg -vv

Zaptel Configuration
======================

SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)

Channel map:

Channel 01: Individual Clear channel (Default) (Slaves: 01)
Channel 02: Individual Clear channel (Default) (Slaves: 02)
Channel 03: Individual Clear channel (Default) (Slaves: 03)
Channel 04: Individual Clear channel (Default) (Slaves: 04)
Channel 05: Individual Clear channel (Default) (Slaves: 05)
Channel 06: Individual Clear channel (Default) (Slaves: 06)
Channel 07: Individual Clear channel (Default) (Slaves: 07)
Channel 08: Individual Clear channel (Default) (Slaves: 08)
Channel 09: Individual Clear channel (Default) (Slaves: 09)
Channel 10: Individual Clear channel (Default) (Slaves: 10)
Channel 11: Individual Clear channel (Default) (Slaves: 11)
Channel 12: Individual Clear channel (Default) (Slaves: 12)
Channel 13: Individual Clear channel (Default) (Slaves: 13)
Channel 14: Individual Clear channel (Default) (Slaves: 14)
Channel 15: Individual Clear channel (Default) (Slaves: 15)
Channel 16: D-channel (Default) (Slaves: 16)
Channel 17: Individual Clear channel (Default) (Slaves: 17)
Channel 18: Individual Clear channel (Default) (Slaves: 18)
Channel 19: Individual Clear channel (Default) (Slaves: 19)
Channel 20: Individual Clear channel (Default) (Slaves: 20)
Channel 21: Individual Clear channel (Default) (Slaves: 21)
Channel 22: Individual Clear channel (Default) (Slaves: 22)
Channel 23: Individual Clear channel (Default) (Slaves: 23)
Channel 24: Individual Clear channel (Default) (Slaves: 24)
Channel 25: Individual Clear channel (Default) (Slaves: 25)
Channel 26: Individual Clear channel (Default) (Slaves: 26)
Channel 27: Individual Clear channel (Default) (Slaves: 27)
Channel 28: Individual Clear channel (Default) (Slaves: 28)
Channel 29: Individual Clear channel (Default) (Slaves: 29)
Channel 30: Individual Clear channel (Default) (Slaves: 30)
Channel 31: Individual Clear channel (Default) (Slaves: 31)

31 channels configured.


root at asterisk:/usr/src# lsmod
Module                  Size  Used by    Not tainted
wct4xxp                51680   0  (unused)
zaptel                175904   0  [wct4xxp]


root at asterisk:/usr/src# cat /proc/pci

  Bus  2, device   9, function  0:
    Communication controller: PCI device 10ee:0314 (Xilinx Corporation) (rev
1).
      IRQ 3.
      Master Capable.  Latency=64.
      Non-prefetchable 32 bit memory at 0xf7eef800 [0xf7eef87f].


root at asterisk:/usr/src# cat /proc/interrupts
           CPU0
  0:     115864          XT-PIC  timer
  1:        141          XT-PIC  keyboard
  2:          0          XT-PIC  cascade
  3:          0          XT-PIC  t4xxp
  5:       2583          XT-PIC  eth0
  8:          1          XT-PIC  rtc
 10:          0          XT-PIC  Intel ICH5
 14:       2639          XT-PIC  ide0
NMI:          0
ERR:          0


root at asterisk:/usr/src# dmesg 

Zapata Telephony Interface Registered on major 196
PCI: Found IRQ 3 for device 02:09.0
Found TE410P at base address f7eef800, remapped to e0978800
TE410P version c01a009b, burst ON
FALC version: 00000005, Board ID: 00
Reg 0: 0x1eec6800
Reg 1: 0x1eec6000
Reg 2: 0x07fc07fc
Reg 3: 0x00000000
Reg 4: 0x00000000
Reg 5: 0x00000000
Reg 6: 0xc01a009b
Reg 7: 0x00001f00
Reg 8: 0x00000000
Reg 9: 0x00ff0000
Reg 10: 0x00000000
TE410P: Launching card: 0
TE410P: Setting up global serial parameters
Found a Wildcard: Wildcard TE410P-Xilinx
Registered tone zone 11 (Italy)
TE410P: Span 1 configured for CCS/HDB3/CRC4
SPAN 1: Primary Sync Source
TE410P: Span 1 configured for CCS/HDB3/CRC4
SPAN 1: Primary Sync Source
Registered tone zone 11 (Italy)


The jumpers are on E1, and the crossed cable should be ok. 

Without loading the module the LED glows in red colour, but the moment we
load module, it goes off. (No red or green).
We ran zttool and tried to run a loop test, but zttool simply hung with the
message 'Looping UP Span 1...'. We had to terminate zttool with 'kill'.
 
What's wrong ?

Thanks,
pixer