[Asterisk-Users] Should this work?

[Angus Comber]

I changed to:

exten => _X.,1,Dial(ZAP/1/${EXTEN},60)
exten => _X.,2,Hangup

But still didn't work.

even though could see channel with zap show channels - saw a channel 1

Angus



  ----- Original Message ----- 
  From: Jason Walker 
  To: Asterisk Users Mailing List - Non-Commercial Discussion 
  Sent: Monday, July 25, 2005 8:45 PM
  Subject: Re: [Asterisk-Users] Should this work?


  Have you defined the context "default" in the extensions.conf for outbound dialing in the globals section?

  For example, I have my ZAP channels identified as OUTBND1 not ZAP in the global section. This new global identifier is pointed to ZAP/g1

  [globals]
  OUTBND1=Zap/g1


  Instead of ZAP in my dial plan to call out, I use ${OUTBND1}.

  Yours:

  ; for dialing outbound - over ISDN line - this bit does not work
  exten => _9XX.,2,Dial(ZAP/g1/${EXTEN},60)
  exten => _9XX.,2,Hangup

  Mine would look like this
  exten => _9XX.,1,Dial(${OUTBND1}/${EXTEN},##)
  exten => _9XX.,2,Hangup


  This helps me to keep track of inbound T1s and outbound T1s.

  Also, you have 2 (2) priorities listed in your example. You can't really do this.

  JASON WALKER
    ----- Original Message ----- 
    From: Angus Comber 
    To: asterisk-users at lists.digium.com 
    Sent: Monday, July 25, 2005 8:11 AM
    Subject: [Asterisk-Users] Should this work?


    Hello

    I am using a Junghans quadBRI ISDN card and it is loaded and working.  In Asterisk if I connect to ISDN line it is detected and tells me so.

    In my zapata.conf I have (abbreviated):

    [channels]
    switchtype=euroisdn
    signalling = bri_cpe

    context=default
    group=1
    channel => 1-2

    ;plus group 2 - 4


    zaptel.conf:
    loadzone=uk
    defaultzone=uk
    # qozap span definitions
    # most of the values should be bogus because we are not really zaptel
    span=1,1,3,ccs,ami
    span=2,0,3,ccs,ami
    span=3,0,3,ccs,ami
    span=4,0,3,ccs,ami

    bchan=1,2
    dchan=3
    bchan=4,5
    dchan=6
    bchan=7,8
    dchan=9
    bchan=10,11
    dchan=12



    Then in extensions.conf I have:

    [default]
    ; this below for internal extensions - works OK
    exten => _2XX,1,Dial(SIP/${EXTEN},20,Ttm)

    ; for dialing outbound - over ISDN line - this bit does not work
    exten => _9XX.,2,Dial(ZAP/g1/${EXTEN},60)
    exten => _9XX.,2,Hangup

    Error I get is:

        -- Executing Dial("SIP/200-e433", "ZAP/g1/902088787367|60") in new stack
    Jul 25 11:56:33 NOTICE[6723]: app_dial.c:777 dial_exec: Unable to create channel of type 'ZAP'
      == Everyone is busy/congested at this time
        -- Executing Hangup("SIP/200-e433", "") in new stack
      == Spawn extension (default, 902088787367, 2) exited non-zero on 'SIP/200-e433'



    I am dialing with sip phones.  They work if dialing extensions internally but not if try to dial outside - eg dial 9 followed by number.

    What have I not done right?

    Angus



----------------------------------------------------------------------------


    _______________________________________________
    Asterisk-Users mailing list
    Asterisk-Users at lists.digium.com
    http://lists.digium.com/mailman/listinfo/asterisk-users
    To UNSUBSCRIBE or update options visit:
       http://lists.digium.com/mailman/listinfo/asterisk-users


------------------------------------------------------------------------------


  _______________________________________________
  Asterisk-Users mailing list
  Asterisk-Users at lists.digium.com
  http://lists.digium.com/mailman/listinfo/asterisk-users
  To UNSUBSCRIBE or update options visit:
     http://lists.digium.com/mailman/listinfo/asterisk-users
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050725/b06cb4d2/attachment.htm