[Asterisk-Users] DELL 2800 : PCI Parity error
Rod Bacon
rod.bacon at empoweredcomms.com.au
Sun Jul 10 15:20:26 MST 2005
I too had this problem, on a 2850, as well as the occasional missed IRQ.
I went through all the usual zaptel tuning stuff.... Disabled fb, disabled ht, disabled acpi (left io-apic enabled), then moved irq affinity of zaptel
card to second CPU so all interrupts from zaptel are on their own. My systems now run close to 100% in zttest, never miss an irq and don't seem to
generate PCI parity errors any more.
I don't know if I've fixed it, but you should really go through the whole process anyway.
==========================================
Rod Bacon
Empowered Communications
Ground Floor, 102 York St. South Melbourne
Victoria, Australia. 3205
Phone: +613 99401600 Fax: +613 99401650
FWD: 512237 ICQ: 5662270
==========================================
list wrote:
> Still not resolved
>
> On Wed, 2005-06-08 at 01:16, David John Walsh wrote:
>
>>Frank
>>
>>Did you ever resolve this? If so what was the issue?
>>
>>On 03/05/05, list <list at nax.no> wrote:
>>
>>>Hi,
>>>I am struggling to get rid of a conflict on DELL 2800 : PCI Parity error
>>>(EB113 on the display)
>>>I am learning linux and asterisk as I go along, there might be obvious
>>>things I should know, but bear with me.
>>>
>>>>From demsg below my 2 digium cards installed are listed (no config or
>>>connections done to digium cards yet), the conflict is with the TDM400P
>>>card, without that card, in any slot, no alarm.
>>>
>>> Zapata Telephony Interface Registered on major 196
>>> Registered Tormenta2 PCI
>>> Controller version: 24
>>> FALC version: 00000000
>>> TE110P: Setting up global serial parameters for E1 FALC V1.2
>>> TE110P: Successfully initialized serial bus for card
>>> Found a Wildcard: Digium Wildcard TE110P T1/E1
>>> Freshmaker version: 71
>>> Freshmaker passed register test
>>> Uhhuh. NMI received. Dazed and confused, but trying to continue
>>> You probably have a hardware problem with your RAM chips
>>> Module 0: Installed -- AUTO FXS/DPO
>>> Module 1: Not installed
>>> Module 2: Not installed
>>> Module 3: Installed -- AUTO FXO (FCC mode)
>>> Found a Wildcard TDM: Wildcard TDM400P REV E/F (4 modules)
>>> Registered tone zone 8 (Norway)
>>> TE110P: Span configured for CCS/HDB3/CRC4
>>> Calling startup (flags is 4099)
>>> wcte1xxp: Setting yellow alarm
>>> usb.c: registered new driver wcusb
>>> Wildcard USB FXS Interface driver registered
>>> TE110P: Span configured for CCS/HDB3/CRC4
>>> Calling startup (flags is 4099)
>>> Registered tone zone 8 (Norway)
>>> TE110P: Span configured for CCS/HDB3/CRC4
>>> Calling startup (flags is 4099)
>>> Registered tone zone 8 (Norway)
>>>
>>>ramchip problem is false, without the card all ok, ramtests on machine
>>>as well.
>>>
>>>lsmod shows wcusb driver on zaptel, I dont need that, can I remove it?
>>>is that a problem or not?
>>>
>>> # lsmod
>>> Module Size Used by Not tainted
>>> usbserial 23964 0 (autoclean) (unused)
>>> lp 9156 0 (autoclean)
>>> parport 38848 0 (autoclean) [lp]
>>> autofs4 16984 0 (autoclean) (unused)
>>> wcusb 19552 0 (unused)
>>> wctdm 41088 0 (unused)
>>> wcte11xp 22048 0 (unused)
>>> zaptel 182080 4 [wcusb wctdm wcte11xp]
>>> e1000 77884 1 (autoclean)
>>> floppy 57552 0 (autoclean)
>>> sg 37388 0 (autoclean)
>>> microcode 6912 0 (autoclean)
>>> ide-cd 34016 0 (autoclean)
>>> cdrom 32896 0 (autoclean) [ide-cd]
>>> keybdev 2976 0 (unused)
>>> mousedev 5688 1
>>> hid 22308 0 (unused)
>>> input 6176 0 [keybdev mousedev hid]
>>> ehci-hcd 20776 0 (unused)
>>> usb-uhci 26860 0 (unused)
>>> usbcore 81152 1 [usbserial wcusb hid ehci-hcd
>>> usb-uhci]
>>> ext3 89960 6
>>> jbd 55060 6 [ext3]
>>> megaraid2 38344 7
>>> diskdumplib 5228 0 [megaraid2]
>>> sd_mod 13904 14
>>> scsi_mod 115112 2 [sg megaraid2 sd_mod]
>>>
>>>finally my interrupts, bit confusing to me, looks like I have dual
>>>processor, can see the NMI but what else can be found here?
>>>
>>> # cat /proc/interrupts
>>> CPU0 CPU1
>>> 0: 3298395 3303167 IO-APIC-edge timer
>>> 1: 3300 2876 IO-APIC-edge keyboard
>>> 2: 0 0 XT-PIC cascade
>>> 8: 0 1 IO-APIC-edge rtc
>>> 12: 236637 237965 IO-APIC-edge PS/2 Mouse
>>> 14: 261779 262965 IO-APIC-edge ide0
>>> 16: 0 0 IO-APIC-level usb-uhci
>>> 18: 0 0 IO-APIC-level usb-uhci
>>> 19: 0 0 IO-APIC-level usb-uhci
>>> 23: 0 24 IO-APIC-level ehci-hcd
>>> 29: 33133540 32846566 IO-APIC-level t1xxp
>>> 38: 72500 83317 IO-APIC-level megaraid
>>> 58: 32838989 33150525 IO-APIC-level wctdm
>>> 72: 222855 12 IO-APIC-level eth0
>>> NMI: 1 0
>>> LOC: 6601462 6601460
>>> ERR: 0
>>> MIS: 0
>>>
>>>any suggestions from someone experienced something similar?
>>>
>>>regards
>>>Frank
>>>_______________________________________________
>>>Asterisk-Users mailing list
>>>Asterisk-Users at lists.digium.com
>>>http://lists.digium.com/mailman/listinfo/asterisk-users
>>>To UNSUBSCRIBE or update options visit:
>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>>
>>
>>_______________________________________________
>>Asterisk-Users mailing list
>>Asterisk-Users at lists.digium.com
>>http://lists.digium.com/mailman/listinfo/asterisk-users
>>To UNSUBSCRIBE or update options visit:
>> http://lists.digium.com/mailman/listinfo/asterisk-users
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
More information about the asterisk-users
mailing list