[Asterisk-Users] Sangoma A104 - D-Channel problem

[Daniel Bichara]

Hi,

Did you tried to set your DMA or SATA as described at message "Sangoma 
A102 cards testing FIXED"?

Daniel

Kumak wrote:

>Hello,
>I have following problem with Sangoma A104 card:
>
>CLI> pri show span 1
>Primary D-channel: 16
>Status: Provisioned, Down, Active
>Switchtype: EuroISDN
>Type: CPE
>Window Length: 0/7
>Sentrej: 0
>SolicitFbit: 0
>Retrans: 0
>Busy: 0
>Overlap Dial: 0
>T200 Timer: 1000
>T203 Timer: 10000
>T305 Timer: 30000
>T308 Timer: 4000
>T313 Timer: 4000
>N200 Counter: 3
>
>NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1
>NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1
>NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1
>NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1
>
>Any idea how to fix it?
>
>My configs:
>
>zaptel.conf:
>
>span=1,1,1,ccs,hdb3,crc4
>bchan=1-15,17-31
>dchan=16
>
>zapata.conf
>
>[channels]
>switchtype=euroisdn
>pridialplan=unknown
>overlapdial=no
>usecallerid=yes
>hidecallerid=yes
>callwaiting=no
>callwaitingcallerid=no
>threewaycalling=no
>transfer=no
>cancallforward=no
>callreturn=no
>jitterbuffers=4
>echocancel=yes
>echocancelwhenbridged=no
>echotraining=yes
>relaxdtmf=yes
>rxgain=0.5
>txgain=0.9
>immediate=no
>amaflags=billing
>adsi=no
>busydetect=no
>callprogress=no
>context = zapline1
>switchtype = euroisdn
>group=1
>signalling = pri_cpe
>channel => 1-15
>channel => 17-31
>
>cat /proc/zaptel/1 :
>
>Span 1: WPE1/0 "wanpipe1 card 0" HDB3//CRC4
>
>           1 WPE1/0/1 Clear (In use)
>           2 WPE1/0/2 Clear (In use)
>           3 WPE1/0/3 Clear (In use)
>           4 WPE1/0/4 Clear (In use)
>           5 WPE1/0/5 Clear (In use)
>           6 WPE1/0/6 Clear (In use)
>           7 WPE1/0/7 Clear (In use)
>           8 WPE1/0/8 Clear (In use)
>           9 WPE1/0/9 Clear (In use)
>          10 WPE1/0/10 Clear (In use)
>          11 WPE1/0/11 Clear (In use)
>          12 WPE1/0/12 Clear (In use)
>          13 WPE1/0/13 Clear (In use)
>          14 WPE1/0/14 Clear (In use)
>          15 WPE1/0/15 Clear (In use)
>          16 WPE1/0/16 HDLCFCS (In use)
>          17 WPE1/0/17 Clear (In use)
>          18 WPE1/0/18 Clear (In use)
>          19 WPE1/0/19 Clear (In use)
>          20 WPE1/0/20 Clear (In use)
>          21 WPE1/0/21 Clear (In use)
>          22 WPE1/0/22 Clear (In use)
>          23 WPE1/0/23 Clear (In use)
>          24 WPE1/0/24 Clear (In use)
>          25 WPE1/0/25 Clear (In use)
>          26 WPE1/0/26 Clear (In use)
>          27 WPE1/0/27 Clear (In use)
>          28 WPE1/0/28 Clear (In use)
>          29 WPE1/0/29 Clear (In use)
>          30 WPE1/0/30 Clear (In use)
>          31 WPE1/0/31 Clear (In use)
>
>
>Information from dmesg:
>
>Processing WAN device wanpipe1...
>wanpipe1: Locating: A104 card, CPU A, PciSlot=8, PciBus=0
>wanpipe1: Found: A104 card, CPU A, PciSlot=8, PciBus=0, Port=0
>PCI: Found IRQ 10 for device 00:08.0
>wanpipe1: AFT PCI memory at 0xEE000000
>wanpipe1: IRQ 10 allocated to the AFT PCI card
>wanpipe1: Initializing for SMP
>wanpipe1: Starting AFT Quad Hardware Init.
>wanpipe1: Enabling front end link monitor
>wanpipe1: Global Chip Configuration: used=1
>wanpipe1: Global Front End Configuraton!
>wanpipe1: T1/E1/J1 Global configuration!
>wanpipe1: AFT Data Mux Bit Map: 0x76543210
>wanpipe1: Setting E1 configuration (Port 1)!
>wanpipe1: All channels enabled
>wanpipe1: Front end successful
>wanpipe1: AFT Security: UnChannelised
>wanpipe1: Configuring Device   :wanpipe1  FrmVr=8
>wanpipe1:    Global MTU   = 1500
>wanpipe1:    Global MRU   = 1500
>wanpipe1:    Data Mux Map = 0x76543210
>wanpipe1: Configuring Interface: w1g1
>wanpipe1:w1g1: Running in TDM Voice mode.
>wanpipe1: AFT Fifo Level Map: 0x02082082
>wanpipe1: Registering interface to Zaptel span # 1!
>wanpipe1:    MRU           :248
>wanpipe1:    MTU           :248
>wanpipe1:    HDLC Eng      :Off (Transparent)
>wanpipe1:    Data Mux Ctrl :On
>wanpipe1:w1g1: Active channels = 0xFFFFFFFE
>wanpipe1:w1g1: Setting first time slot to 1
>wanpipe1:w1g1: Config for Transparent mode: Idle=0 Len=248
>wanpipe1:w1g1: Allocating 65 dma skb len=256 Chaining=Off
>
>
>_______________________________________________
>Asterisk-Users mailing list
>Asterisk-Users at lists.digium.com
>http://lists.digium.com/mailman/listinfo/asterisk-users
>To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
>  
>