[Asterisk-Users] Sangoma A104 - D-Channel problem

[Kumak]

Hello,
I have following problem with Sangoma A104 card:

CLI> pri show span 1
Primary D-channel: 16
Status: Provisioned, Down, Active
Switchtype: EuroISDN
Type: CPE
Window Length: 0/7
Sentrej: 0
SolicitFbit: 0
Retrans: 0
Busy: 0
Overlap Dial: 0
T200 Timer: 1000
T203 Timer: 10000
T305 Timer: 30000
T308 Timer: 4000
T313 Timer: 4000
N200 Counter: 3

NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1
NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1
NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1
NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1

Any idea how to fix it?

My configs:

zaptel.conf:

span=1,1,1,ccs,hdb3,crc4
bchan=1-15,17-31
dchan=16

zapata.conf

[channels]
switchtype=euroisdn
pridialplan=unknown
overlapdial=no
usecallerid=yes
hidecallerid=yes
callwaiting=no
callwaitingcallerid=no
threewaycalling=no
transfer=no
cancallforward=no
callreturn=no
jitterbuffers=4
echocancel=yes
echocancelwhenbridged=no
echotraining=yes
relaxdtmf=yes
rxgain=0.5
txgain=0.9
immediate=no
amaflags=billing
adsi=no
busydetect=no
callprogress=no
context = zapline1
switchtype = euroisdn
group=1
signalling = pri_cpe
channel => 1-15
channel => 17-31

cat /proc/zaptel/1 :

Span 1: WPE1/0 "wanpipe1 card 0" HDB3//CRC4

           1 WPE1/0/1 Clear (In use)
           2 WPE1/0/2 Clear (In use)
           3 WPE1/0/3 Clear (In use)
           4 WPE1/0/4 Clear (In use)
           5 WPE1/0/5 Clear (In use)
           6 WPE1/0/6 Clear (In use)
           7 WPE1/0/7 Clear (In use)
           8 WPE1/0/8 Clear (In use)
           9 WPE1/0/9 Clear (In use)
          10 WPE1/0/10 Clear (In use)
          11 WPE1/0/11 Clear (In use)
          12 WPE1/0/12 Clear (In use)
          13 WPE1/0/13 Clear (In use)
          14 WPE1/0/14 Clear (In use)
          15 WPE1/0/15 Clear (In use)
          16 WPE1/0/16 HDLCFCS (In use)
          17 WPE1/0/17 Clear (In use)
          18 WPE1/0/18 Clear (In use)
          19 WPE1/0/19 Clear (In use)
          20 WPE1/0/20 Clear (In use)
          21 WPE1/0/21 Clear (In use)
          22 WPE1/0/22 Clear (In use)
          23 WPE1/0/23 Clear (In use)
          24 WPE1/0/24 Clear (In use)
          25 WPE1/0/25 Clear (In use)
          26 WPE1/0/26 Clear (In use)
          27 WPE1/0/27 Clear (In use)
          28 WPE1/0/28 Clear (In use)
          29 WPE1/0/29 Clear (In use)
          30 WPE1/0/30 Clear (In use)
          31 WPE1/0/31 Clear (In use)


Information from dmesg:

Processing WAN device wanpipe1...
wanpipe1: Locating: A104 card, CPU A, PciSlot=8, PciBus=0
wanpipe1: Found: A104 card, CPU A, PciSlot=8, PciBus=0, Port=0
PCI: Found IRQ 10 for device 00:08.0
wanpipe1: AFT PCI memory at 0xEE000000
wanpipe1: IRQ 10 allocated to the AFT PCI card
wanpipe1: Initializing for SMP
wanpipe1: Starting AFT Quad Hardware Init.
wanpipe1: Enabling front end link monitor
wanpipe1: Global Chip Configuration: used=1
wanpipe1: Global Front End Configuraton!
wanpipe1: T1/E1/J1 Global configuration!
wanpipe1: AFT Data Mux Bit Map: 0x76543210
wanpipe1: Setting E1 configuration (Port 1)!
wanpipe1: All channels enabled
wanpipe1: Front end successful
wanpipe1: AFT Security: UnChannelised
wanpipe1: Configuring Device   :wanpipe1  FrmVr=8
wanpipe1:    Global MTU   = 1500
wanpipe1:    Global MRU   = 1500
wanpipe1:    Data Mux Map = 0x76543210
wanpipe1: Configuring Interface: w1g1
wanpipe1:w1g1: Running in TDM Voice mode.
wanpipe1: AFT Fifo Level Map: 0x02082082
wanpipe1: Registering interface to Zaptel span # 1!
wanpipe1:    MRU           :248
wanpipe1:    MTU           :248
wanpipe1:    HDLC Eng      :Off (Transparent)
wanpipe1:    Data Mux Ctrl :On
wanpipe1:w1g1: Active channels = 0xFFFFFFFE
wanpipe1:w1g1: Setting first time slot to 1
wanpipe1:w1g1: Config for Transparent mode: Idle=0 Len=248
wanpipe1:w1g1: Allocating 65 dma skb len=256 Chaining=Off