[Asterisk-Users] Asterisk@Home .5 Setup help with 4 X100P {Scanned}

[Asterisk at Home]

Have you tried the new auto-config script? Type
help-aah for more info.

--- goldhorse <goldhorse at yahoo.co.jp> wrote:

> If you have 4 fxo cards I think you should modify
> zapata.conf to
> channel => 1-4
> I haven't used asterisk at home so I don't know how it
> starts asterisk, 
> but just a thought,
> does it do modprobe wcfxo then ztcfg? Try doing this
> at the terminal, 
> if something's
> wrong you should get error messages.
> 
> Hope this helps.
> 
> Daniel
> 
> 
> On 2005/02/16, at 4:18, Rich Adamson wrote:
> 
> >
> >> I removed the ; before channel => 1 and restarted
> * and I get an 
> >> error.
> >>
> >> Ouch ... error while writing audio data: : Broken
> pipe
> >>
> >> ?????
> >>
> >> I then replaced the ; and its starts??
> >>
> >> I'm upgrading from .4 to .5
> >>
> >> .4 was running
> >>
> >> Thanks, David
> >>
> >>
> >>
> >> On Tue, 2005-02-15 at 12:46 -0500, dean collins
> wrote:
> >>> David,
> >>> You will need to go into the Zapata.conf file
> and remove the ; before
> >>> channel => 1
> >>>
> >>> (modify it to suit however you want to set up
> your 4 X100p lines.
> >>>
> >>> The outgoing lines you see in FOP are only
> example lines, you will 
> >>> need
> >>> to modify FOP to get rid of them etc.
> >>>
> >>>
> >>> -----Original Message-----
> >>> From: asterisk-users-bounces at lists.digium.com
> >>> [mailto:asterisk-users-bounces at lists.digium.com]
> On Behalf Of David 
> >>> Shaw
> >>> Sent: Tuesday, February 15, 2005 11:02 AM
> >>> To: Asterisk Users Mailing List - Non-Commercial
> Discussion
> >>> Subject: [Asterisk-Users] Asterisk at Home .5 Setup
> help with 4 X100P
> >>>
> >>> Hello All, I installed Asterisk at Home .5 last
> night. I was able to
> >>> configure some extensions for the house and they
> work fine. I just 
> >>> can't
> >>> make inbound and/or outbound calls. The Flash
> Operator Panel shows 
> >>> four
> >>> external icons and my new extensions.
> >>>
> >>> I have four X100P and two Broadvoice sip
> accounts.
> >>>
> >
> >
> > The broken pipe message usually means something is
> misconfigured. Check
> > your zapata.conf against the following:
> >
> > context=inbound-bus
> > signalling=fxs_ks
> > echocancel=yes
> > echotraining=800
> > echocancelwhenbridged=no
> > rxgain=3.0
> > txgain=0.0
> > immediate=yes
> > channel => 1
> >
> > After making changes to zapata.conf, be sure to
> stop and start *.
> > Don't use reload on these type changes.
> >
> >
> >
> > _______________________________________________
> > Asterisk-Users mailing list
> > Asterisk-Users at lists.digium.com
> >
>
http://lists.digium.com/mailman/listinfo/asterisk-users
> > To UNSUBSCRIBE or update options visit:
> >   
>
http://lists.digium.com/mailman/listinfo/asterisk-users
> >
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
>
http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>   
>
http://lists.digium.com/mailman/listinfo/asterisk-users
> 



		
__________________________________ 
Do you Yahoo!? 
Read only the mail you want - Yahoo! Mail SpamGuard. 
http://promotions.yahoo.com/new_mail