[Asterisk-Users] Re: Fw: AU caller ID with Sipura SPA-3000

[Eric Bishop]

This is exactly what I did and I suspect why you are not getting
caller ID either. If you put in a NoOp,${CALLERID} I think you'll find
the Sipura is passing the letter A followed by the username it using
in in sip.conf as the caller id number rather than A followed by the
number of the caller. It seems the Sipura is unable to extract caller
ID from AU phone lines.....


On Sat, 5 Feb 2005 19:16:40 +1000, Peter Illmayer <pete at jbo.com.au> wrote:
> Eric
> 
> This is what I did...
> 
> http://voxilla.com/forum-viewtopic-t-1335.html
> 
> very clever
> 
> --
> Open WebMail Project (http://openwebmail.org)
> 
> ---------- Original Message -----------
> From: Eric Bishop <asterisk.eric at gmail.com>
> To: Peter Illmayer <pete at jbo.com.au>
> Sent: Sat, 5 Feb 2005 15:38:47 +1100
> Subject: Re: Fw: [Asterisk-Users] AU caller ID with Sipura SPA-3000
> 
> > Hi Peter,
> >
> > The caller number I get into Asterisk is the username that Sipura is
> > using to register with Asterisk, not the actual caller ID number of
> > the caller. If you are in fact getting the the caller ID passed to
> > Asterisk would you mind sending me a screen shot of the "PSTN Line"
> > and Line 1" tabs from your sipura config, also the relevant sections
> > of your sip.conf and extensions.conf
> >
> > Thanks....
> >
> > Eric.
> >
> > On Sat, 5 Feb 2005 08:15:28 +1000, Peter Illmayer <pete at jbo.com.au> wrote:
> > > Hi Eric
> > >
> > > Not sure as to your question... I can get the callerid to be presented to
> > > asterisk fine.  What I cant do as yet is to get the calleridnum to display on
> > > the phone.  I can replace the calleridname as teh calleridnum and display that
> > > on the phone but the sipura wont allow me to stick the number in the number
> > > field which is causing me LOTS of grief with selective ring tones.
> > >
> > > If your stuck at teh first point, mail me and I'll give you some pointers as I
> > > can see the correct callerid in asterisk via an inbound PSTN call routed via
> > > sipura
> > >
> > > Pete
> > >
> > >
> > > ---------- Forwarded Message -----------
> > > From: Eric Bishop <asterisk.eric at gmail.com>
> > > To: Asterisk Users Mailing List - Non-Commercial Discussion
> > > <asterisk-users at lists.digium.com>
> > > Sent: Sat, 5 Feb 2005 08:28:52 +1100
> > > Subject: [Asterisk-Users] AU caller ID with Sipura SPA-3000
> > >
> > > Hi All,
> > >
> > > I am using a Sipura SPA-3000 as an FXO gateway to bring calls in and
> > > out of Asterisk. I am using "PSTN Ring Thru Line 1" (on the "PSTN
> > > Line" tab) so Asterisk answers the call rather than the SPA-3000. It
> > > is all working perfectly except I can't get the SPA-3000 to pass
> > > caller ID to Asterisk. It passes "Display Name", "User ID" and any
> > > "PSTN CID Number Prefix" I have configured.
> > >
> > > I have adjusted "PSTN Ring Thru Delay" to 10 as I realise caller ID is
> > > not presented until the second ring in oz. I have also verified that
> > > caller ID is enabled on the line (with an analogue LCD handset).
> > >
> > > Has any aussie out there had success getting the SPA-3000 to pass
> > > caller ID to Asterisk?
> > >
> > > The only settings I havn't played with yet is "Caller ID Method" (on
> > > the Regional tab). It is set to the default of "Bellcore (N.Amer,
> > > China)" which I beleive is correct.
> > > _______________________________________________
> > > Asterisk-Users mailing list
> > > Asterisk-Users at lists.digium.com
> > > http://lists.digium.com/mailman/listinfo/asterisk-users
> > > To UNSUBSCRIBE or update options visit:
> > >    http://lists.digium.com/mailman/listinfo/asterisk-users
> > > ------- End of Forwarded Message -------
> > >
> > > --
> > > Open WebMail Project (http://openwebmail.org)
> > >
> > >
> ------- End of Original Message -------
> 
>