[Asterisk-Users] HELP! X100P IRQ conflict w/ USB
163
luzw at 163.com
Thu Aug 4 22:17:05 MST 2005
Thanks a lot for you help first.
I tried to load the drivers, but failed.
--------------------------------------------------------------------
[root at qhserver voicepet-single-x100p]# /sbin/modprobe zaptel
modprobe: Can't locate module zaptel
[root at qhserver voicepet-single-x100p]# pwd
/home/shengl/voicepet-single-x100p
--------------------------------------------------------------------
>
> Have you loaded the zaptel drivers yet? Until you load the wcfxo module you
> will see nothing in /proc/interrupts.
>
> Cheers,
> Peter
>
> -----Original Message-----
> From: asterisk-users-bounces at lists.digium.com
> [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of 163
> Sent: Friday, 5 August 2005 12:35 PM
> To: asterisk-users at lists.digium.com
> Subject: [Asterisk-Users] HELP! X100P IRQ conflict w/ USB
>
>
> PC: HP Vetra VL400
> Mainbood: Intel815
> BIOS: Phonix 4.0 release 6.0
> OS: REDHAT 9.0
> I installed the X100P in PCI slot 2 and disable the USB port, serial-port
> and parallel-port in BIOS. I can't found the X100P card in " cat interrupts"
> But I can found the card in the "cat ioports" use "lspci" I found the
> X100Pcard use the interrupts 11 too. Who can help me to solve this problem?
>
> -----------------------------------------------
> [root at qhserver proc]# cat interrupts
> CPU0
> 0: 28561 XT-PIC timer
> 1: 6 XT-PIC keyboard
> 2: 0 XT-PIC cascade
> 5: 2954 XT-PIC eth0
> 8: 1 XT-PIC rtc
> 11: 0 XT-PIC usb-uhci
> 12: 29 XT-PIC PS/2 Mouse
> 14: 7199 XT-PIC ide0
> 15: 1 XT-PIC ide1
> NMI: 0
> ERR: 0
> -------------------------------------------------
>
> -------------------------------------------------
> [root at qhserver proc]# cat ioports
> 0000-001f : dma1
> 0020-003f : pic1
> 0040-005f : timer
> 0060-006f : keyboard
> 0070-007f : rtc
> 0080-008f : dma page reg
> 00a0-00bf : pic2
> 00c0-00df : dma2
> 00f0-00ff : fpu
> 0170-0177 : ide1
> 01f0-01f7 : ide0
> 0376-0376 : ide1
> 0378-037a : parport0
> 037b-037f : parport0
> 03c0-03df : vga+
> 03f6-03f6 : ide0
> 0cf8-0cff : PCI conf1
> 1800-180f : Intel Corp. 82801AA IDE
> 1800-1807 : ide0
> 1808-180f : ide1
> 1810-181f : Intel Corp. 82801AA SMBus
> 1820-183f : Intel Corp. 82801AA USB
> 1820-183f : usb-uhci
> 2000-20ff : Tiger Jet Network Inc. Model 300 128k
> 2400-247f : 3Com Corporation 3c905C-TX/TX-M [Tornado]
> 2400-247f : 01:04.0
> ------------------------------------------------------
>
> ----------------------------------------------------------------------------
> ----
> [root at qhserver sbin]# ./lspci -vvv
> 00:00.0 Host bridge: Intel Corp. 82815 815 Chipset Host Bridge and Memory
> Contr)
> Subsystem: Intel Corp. 82815 815 Chipset Host Bridge and Memory
> Controlb
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Ste-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort--
> Latency: 0
> Capabilities: [88] #09 [f104]
>
> 00:02.0 VGA compatible controller: Intel Corp. 82815 CGC [Chipset Graphics
> Cont)
> Subsystem: Hewlett-Packard Company: Unknown device 1245
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Ste-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbor-
> Latency: 0
> Interrupt: pin A routed to IRQ 10
> Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M]
> Region 1: Memory at ec000000 (32-bit, non-prefetchable) [size=512K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3ho)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:1e.0 PCI bridge: Intel Corp. 82801AA PCI Bridge (rev 02) (prog-if 00
> [Normal)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Ste-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort--
> Latency: 0
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
> I/O behind bridge: 00002000-00002fff
> Memory behind bridge: ec100000-ec1fffff
> Prefetchable memory behind bridge: fff00000-000fffff
> BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
>
> 00:1f.0 ISA bridge: Intel Corp. 82801AA ISA Bridge (LPC) (rev 02)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
> Ste-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbor-
> Latency: 0
>
> 00:1f.1 IDE interface: Intel Corp. 82801AA IDE (rev 02) (prog-if 80
> [Master])
> Subsystem: Intel Corp. 82801AA IDE
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Ste-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbor-
> Latency: 0
> Region 4: I/O ports at 1800 [size=16]
>
> 00:1f.2 USB Controller: Intel Corp. 82801AA USB (rev 02) (prog-if 00 [UHCI])
> Subsystem: Intel Corp. 82801AA USB
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Ste-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbor-
> Latency: 0
> Interrupt: pin D routed to IRQ 11
> Region 4: I/O ports at 1820 [size=32]
>
> 00:1f.3 SMBus: Intel Corp. 82801AA SMBus (rev 02)
> Subsystem: Intel Corp. 82801AA SMBus
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Ste-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbor-
> Interrupt: pin B routed to IRQ 9
> Region 4: I/O ports at 1810 [size=16]
>
> 01:01.0 Communication controller: Tiger Jet Network Inc. Intel 537
> Subsystem: Unknown device 8085:0003
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Ste-
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Ste-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbor-
> Latency: 64 (250ns min, 32000ns max)
> Interrupt: pin A routed to IRQ 5
> Region 0: I/O ports at 2000 [size=256]
> Region 1: Memory at ec100000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA
> PME(D0+,D1-,D2+,D3h)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 01:04.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev
> 78)
> Subsystem: Hewlett-Packard Company: Unknown device 1246
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Ste-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbor-
> Latency: 80 (2500ns min, 2500ns max), cache line size 08
> Interrupt: pin A routed to IRQ 5
> Region 0: I/O ports at 2400 [size=128]
> Region 1: Memory at ec101000 (32-bit, non-prefetchable) [size=128]
> Expansion ROM at <unassigned> [disabled] [size=128K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3ho)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
> ----------------------------------------------------------------------------
> ---------
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
>
More information about the asterisk-users
mailing list