[Asterisk-Users] TE11OP -> Mitel 200Sx??
Dennis Walker
dwalker at jackson-tube.com
Fri Apr 22 19:13:02 MST 2005
I have done the same thing with an sx200 and a pri circuit
My sx200 can only do ami d4 and e&m channels
Here's parts of my config that takes the pri and converts it to e&m with
ANI & DNIS
zaptel.conf
# t1 connected to the PRI circuit
span=1,1,0,exf,b8zs
# t1 connected to SX200
# the t1 card on my sx200 did d4 ami and I supplied ANI and DNIS through
the dial plan
span=2,0,0,d4,ami
bchan=1-23
dchan=24
e&m=25-47
---------------------------------------------
zapata.conf
[channels]
echocancel=yes
echocancelwhenbridged=yes
echotraining=no
rxgain=0.0
txgain=0.0
useincomingcalleridonzaptransfer=yes
restrictcid=no
context=default
usecallingpres=yes
usercallerid=yes
hidecallerid=no
callerid="Company Name"<8005551212>
signalling=pri_cpe
switchtype=dms100
group=1
channel => 1-23
group=2
signalling=em_w
emdigitwait=500
channel => 24-47
# I needed the emdigitwait=500 to wait long enough for the SX200 to dial
out it's digits
--------------------------------------------------
extensions.conf
# our PRI circiut gave us the last 4 digits of the dialed number and this
is how I passed
# *ANI*DNIS* to the SX200 for it to decode
# the first group were individual numbers that mapped to faxes and modems
exten => 1234,1,Dial(Zap/g2/*${CALLERIDNUM}*${EXTEN}*,,r)
exten => 5555,1,Dial(Zap/g2/*${CALLERIDNUM}*${EXTEN}*,,r)
exten => 3333,1,Dial(Zap/g2/*${CALLERIDNUM}*${EXTEN}*,,r)
# this set mapped our did 5000 - 5199 to the SX200
exten => _5[0-1]XX,1,Dial(Zap/g2/*${CALLERIDNUM}*${EXTEN}*,,r)
The reset of the dial plan took what ever I set up in the sx200 ARS to dial
out and
sent out put Zap/G1
Hope this helps
----------
From: Henry Devito[SMTP:hdevito at mchsi.com]
Reply To: Asterisk Users Mailing List - Non-Commercial Discussion
Sent: Friday, April 22, 2005 8:56 PM
To: Scott Wolfe; Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??
<<File: ATT00262.html>><<File: ATT00263.txt>>
I was wrong. I just looked in my Mitel I&M's. What level software are you
on in the SX200? Up until a certain level 200's could only do D4/AMI T1's,
they could not do PRI's. If it is a newer switch within the past 3 years
or an older switch with later software than you can do PRI, but the
signaling and framing must be ESF/B8ZS.
Henry
----- Original Message -----
From: Scott Wolfe
To: mike at shelcomm.com ; Asterisk Users Mailing List - Non-Commercial
Discussion
Sent: Friday, April 22, 2005 7:04 PM
Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??
Thanks,
This is what I have now, but my Mitel PBX and Asterisk Box are unable
to communicate via the T1 connection. Asterisk loads ok but I get error
lights (blinking orange) on my TE110P and on my Mitel T1 card. Hummmm
-Scott
/etc/zaptel.conf
loadzone = us
defaultzone=us
span=1,0,0,d4,ami
bchan=1-23
dchan=24
/etc/asterisk/zapata.conf
[trunkgroups]
[channels]
context=default
switchtype=dms100
rxwink=300
usecallerid=no
hidecallerid=no
callwaiting=no
usecallingpres=yes
callwaitingcallerid=no
threewaycalling=yes
transfer=yes
canpark=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
rxgain=0.0 ;into the pstn twords the telco
txgain=0.0
callgroup=1
pickupgroup=1
immediate=yes
signalling=pri_cpe
group=1
context=default
emdigitwait=500
channel => 1-23 ; Set this to 1-15,17-31 for E1
----- Original Message -----
From: Michael D Schelin
To: Asterisk Users Mailing List - Non-Commercial Discussion
Sent: Friday, April 22, 2005 4:48 PM
Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??
Hello Henry
e&m=1-23 should be bchan=1-23
you have it set for analog
also
signaling=pri_cpe
Henry Devito wrote:
Don't you need one of these directives so the PRI knows which is
master and which is slave?
a.. pri_cpe: PRI signaling, CPE side
a.. pri_net: PRI signaling, Network side
Henry
----- Original Message -----
From: Scott Wolfe
To: Asterisk-Users at lists.digium.com
Sent: Friday, April 22, 2005 11:01 AM
Subject: [Asterisk-Users] TE11OP -> Mitel 200Sx??
Hello all. I just received a TE110P and am trying to hook it to my
Mitel 200SX has anyone successfully done this? My configuration is as
follows.
Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card.
All I get is a blinking yellow on my TE110P card and an alarm on my
Mitel. T1 card.
Any advice would be great.
Zaptel.conf
span=1,0,1,d4,ami
e&m=1-23
dchan=24
Zapata.conf
signalling=em_w
switchtype=dms100
echocancel=yes
echocancelwhenbridged=yes
echotraining=400
callerid=asreceived
group=1
context=default
channel => 1-23
------------------------------------------------------------------------
_______________________________________________
Asterisk-Users mailing list
Asterisk-Users at lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
--------------------------------------------------------------------------
_______________________________________________
Asterisk-Users mailing list
Asterisk-Users at lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
------------------------------------------------------------------------
----
_______________________________________________
Asterisk-Users mailing list
Asterisk-Users at lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
------------------------------------------------------------------------
------
_______________________________________________
Asterisk-Users mailing list
Asterisk-Users at lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
More information about the asterisk-users
mailing list