[Asterisk-Users] TE11OP -> Mitel 200Sx??

[Henry Devito]

I was wrong.  I just looked in my Mitel I&M's.  What level software are you on in the SX200?  Up until a certain level 200's could only do D4/AMI T1's, they could not do PRI's.  If it is a newer switch within the past 3 years or an older switch with later software than you can do PRI, but the signaling and framing must be ESF/B8ZS.

Henry
  ----- Original Message ----- 
  From: Scott Wolfe 
  To: mike at shelcomm.com ; Asterisk Users Mailing List - Non-Commercial Discussion 
  Sent: Friday, April 22, 2005 7:04 PM
  Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??




  Thanks,
    This is what I have now, but my Mitel PBX and Asterisk Box are unable to communicate via the T1 connection. Asterisk loads ok but I get error lights (blinking orange) on my TE110P and on my Mitel T1 card. Hummmm


  -Scott

  /etc/zaptel.conf
  loadzone = us
  defaultzone=us
  span=1,0,0,d4,ami
  bchan=1-23
  dchan=24

  /etc/asterisk/zapata.conf
  [trunkgroups]

  [channels]
  context=default
  switchtype=dms100
  rxwink=300
  usecallerid=no
  hidecallerid=no
  callwaiting=no
  usecallingpres=yes
  callwaitingcallerid=no
  threewaycalling=yes
  transfer=yes
  canpark=yes
  cancallforward=yes
  callreturn=yes
  echocancel=yes
  echocancelwhenbridged=yes
  rxgain=0.0 ;into the pstn twords the telco
  txgain=0.0
  callgroup=1
  pickupgroup=1
  immediate=yes

  signalling=pri_cpe
  group=1
  context=default 
  emdigitwait=500
  channel => 1-23 ; Set this to 1-15,17-31 for E1




    ----- Original Message ----- 
    From: Michael D Schelin 
    To: Asterisk Users Mailing List - Non-Commercial Discussion 
    Sent: Friday, April 22, 2005 4:48 PM
    Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??


    Hello Henry
    e&m=1-23 should be bchan=1-23
    you have it set for analog
    also
    signaling=pri_cpe


    Henry Devito wrote:

      Don't you need one of these directives so the PRI knows which is master and which is slave?

      a.. pri_cpe: PRI signaling, CPE side 
      a.. pri_net: PRI signaling, Network side 

      Henry
        ----- Original Message ----- 
        From: Scott Wolfe 
        To: Asterisk-Users at lists.digium.com 
        Sent: Friday, April 22, 2005 11:01 AM
        Subject: [Asterisk-Users] TE11OP -> Mitel 200Sx??


        Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows.


        Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card. 


        All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card. 


        Any advice would be great. 


        Zaptel.conf

        span=1,0,1,d4,ami

        e&m=1-23 

        dchan=24 


        Zapata.conf 

        signalling=em_w

        switchtype=dms100

        echocancel=yes

        echocancelwhenbridged=yes

        echotraining=400 

        callerid=asreceived

        group=1

        context=default

        channel => 1-23 




------------------------------------------------------------------------
        _______________________________________________
        Asterisk-Users mailing list
        Asterisk-Users at lists.digium.com
        http://lists.digium.com/mailman/listinfo/asterisk-users
        To UNSUBSCRIBE or update options visit:
           http://lists.digium.com/mailman/listinfo/asterisk-users
--------------------------------------------------------------------------
_______________________________________________
Asterisk-Users mailing list
Asterisk-Users at lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users



----------------------------------------------------------------------------


    _______________________________________________
    Asterisk-Users mailing list
    Asterisk-Users at lists.digium.com
    http://lists.digium.com/mailman/listinfo/asterisk-users
    To UNSUBSCRIBE or update options visit:
       http://lists.digium.com/mailman/listinfo/asterisk-users


------------------------------------------------------------------------------


  _______________________________________________
  Asterisk-Users mailing list
  Asterisk-Users at lists.digium.com
  http://lists.digium.com/mailman/listinfo/asterisk-users
  To UNSUBSCRIBE or update options visit:
     http://lists.digium.com/mailman/listinfo/asterisk-users
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050422/28effd4a/attachment.htm