Fw: [Asterisk-Users] Analogue phone transfering

[David Wilson]

Hi guys,

Any other ideas on this one ?

Kindest regards
David Wilson
_______________________________
D c D a t a
Tel +27 33 342 7003
Fax +27 33 345 4155
Cell +27 82 4147413
http://www.dcdata.co.za
support at dcdata.co.za
Powered by Linux, driven by passion !
_______________________________

"Computers are not intelligent. They only think they are."

----- Original Message ----- 
From: "David Wilson" <dave at dcdata.co.za>
To: "Asterisk Users Mailing List - Non-Commercial Discussion" 
<asterisk-users at lists.digium.com>; <eric at fnords.org>
Sent: Friday, April 15, 2005 3:45 PM
Subject: Re: [Asterisk-Users] Analogue phone transfering


> Hi Eric,
>
> Thanks for your reply and guidance.
> I've tried that but unfortunately am still battling with the same problem.
> Any other ideas ? Thanks for your help so far.
>
> My zapata.conf:
> [channels]
> signalling=fxs_ks
> callprogress=no
> ;causes problems with calls not being established correctly
> context=incoming
> echocancel=yes ; You can set this to 32, 64, or 128, tweak to your needs.
> echocancelwhenbridged=yes
> echotraining=800 ; Asterisk trains to the beginning of the call, number is 
> in milliseconds
> ;echotraining=yes
> usecallerid=yes
> callerid=asreceived
> callwaiting=no
> usedistinctiveringdetection=no
> busydetect=yes
> busycount=8
> adsi=no
> relaxdtmf=yes
> faxdetect=incoming
> channel=1-3
>
> signalling=fxo_ks
> context=default
> relaxdtmf=yes
> ;threewaycalling=yes
> transfer=yes
> adsi=no
> usecallerid=no
> channel=4
>
> ;rxgain=70.0
> ;txgain=50.0
>
>
> Kindest regards
> David Wilson
> _______________________________
> D c D a t a
> Tel +27 33 342 7003
> Fax +27 33 345 4155
> Cell +27 82 4147413
> http://www.dcdata.co.za
> support at dcdata.co.za
> Powered by Linux, driven by passion !
> _______________________________
>
> "Computers are not intelligent. They only think they are."
>
> ----- Original Message ----- 
> From: "Eric Wieling" <eric at fnords.org>
> To: "Asterisk Users Mailing List - Non-Commercial Discussion" 
> <asterisk-users at lists.digium.com>
> Sent: Friday, April 15, 2005 3:21 PM
> Subject: Re: [Asterisk-Users] Analogue phone transfering
>
>
>> David Wilson wrote:
>>
>>> Hi guys,
>>>
>>> How are you keeping ?
>>> I have an analogue phone plugged into a Digium FXS Zap module on my TDM 
>>> card.
>>>
>>> The phone works well except that I cannot seem to transfer calls using 
>>> the "flash" key. I don't seem to get another dialtone as indicated in:
>>> http://www.voip-info.org/wiki-Asterisk+tips+zap+transfer
>>>
>>> Any ideas what I've done wrong ?
>>> This is my zapata.conf:
>>> [channels]
>>> ; For analogue phone
>>> signalling=fxo_ks
>>> context=default
>>> channel=4
>>> relaxdtmf=yes
>>> threewaycalling=yes
>>> transfer=yes
>>> adsi=no
>>> usecallerid=no
>>> rxgain=70.0
>>> txgain=50.0
>>
>>
>> In zapata.conf you set options and then APPLY the options to a channel. 
>> As you can see you are specifying the channel before most of your otions 
>> so they are never applied.  Move your channel= line AFTER the options you 
>> want to set.  You might want to remove your rxgain and txgain so you 
>> don't blow out your eardrums.
>>
>> -- 
>> Always do right. This will gratify some people and astonish the rest.
>> Mark Twain
>> _______________________________________________
>> Asterisk-Users mailing list
>> Asterisk-Users at lists.digium.com
>> http://lists.digium.com/mailman/listinfo/asterisk-users
>> To UNSUBSCRIBE or update options visit:
>>   http://lists.digium.com/mailman/listinfo/asterisk-users
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users