[Asterisk-Users] Setgroup & Checkgroup

[Ronald Wiplinger]

Damian Funnell wrote:

> Hi Ronald,
>
> We use SetGroup/CheckGroup and your syntax appears to be fine (either 
> that or ours is broken too, but it seems to work ok!)
> One question - what lines do you have in priority 1 - 3?  We found 
> that our dial plan would not work unless the first priority (for all 
> extensions) was 1 and unless the priorities increased an integer at a 
> time (not sure if this is by design or not, but was the only way it 
> would work regardless).

It starts correct with 1 (there are some NoOp and ENUM lookup, which is 
not interesting for that case)

>
> Also (and this is really grasping at straws), have you tried using 
> different group names in case 'sip-1x' has any special meaning?  These 
> names can be anything that is meaningful and we use the format 
> 'line28x' for our group names (which works fine).

The real group name is sip-xxxxxxxxxxxx (my phone number) I have shorten 
it at the example.

I read somewhere, if you have TWO or more Setgroup than all previous 
ones will be set to zero back!!! If that is the case than it makes not 
much sense to use it that way I do. As you can see in the CLI outputs, I 
copied, it uses a different name of the group variable.


bye

Ronald

>
> Good luck!
>
>
> Ronald Wiplinger wrote:
>
>> I have some troubles to use Setgroup / Checkgroup!!!
>>
>> I setup a test (NoOP's are deleted): First caller should get first 
>> line, second caller should get second line, third caller should get 
>> busy and send an email. Note, that I used twice here to check the 
>> first line!!!
>>
>>
>>
>> [trunkint_A]
>>
>> exten => _90NZZZZ.,104,SetGroup(sip-13)        ; increase Group counter
>> exten => _90NZZZZ.,105,CheckGroup(1)            ; check no more than 
>> 1 in this group
>> exten => _90NZZZZ.,106,NoOp(Line 106)
>> exten => _90NZZZZ.,107,Dial(SIP/${EXTEN:${TRUNKMSD}}@sip-13)
>> exten => _90NZZZZ.,108,hangup
>> ;
>> exten => _90NZZZZ.,206,SetGroup(sip-12)
>> exten => _90NZZZZ.,207,CheckGroup(1)
>> exten => _90NZZZZ.,208,NoOp(Line 208)
>> exten => _90NZZZZ.,209,Dial(SIP/${EXTEN:${TRUNKMSD}}@sip-12)
>> exten => _90NZZZZ.,210,hangup
>> ;
>> exten => _90NZZZZ.,308,SetGroup(sip-13)
>> exten => _90NZZZZ.,309,CheckGroup(1)
>> exten => _90NZZZZ.,310,NoOp(Line 310)
>> exten => _90NZZZZ.,311,Dial(SIP/${EXTEN:${TRUNKMSD}}@sip-13)
>> exten => _90NZZZZ.,312,hangup
>> ;
>> exten => _90NZZZZ.,410,Busy
>> exten => _90NZZZZ.,411,SYSTEM(mail -s 'VPBX all lines in use' 
>> ronald at elmit.com)
>>
>>
>> I thought that 104 will set the Group counter "sip-13" to "1" and 
>> will use line 107 for the dial command
>> If another caller comes in that way, "sip-13" would be "2" and 
>> because Checkgroup allows only "1", the Group coutner would be 
>> setback to "1" and it will follow the jump to 206 and sets the Group 
>> counter "sip-12" to "1"
>> A third call should now find Group counter sip-12 and sip-13 set to 
>> "1" and give a busy signal and send an email.
>>
>>
>> HOWEVER, the log file show:
>>    -- Executing SetGroup("Local/9xxxxx at Line-optimize-f8c8,2", 
>> "sip-13") in new stack
>>    -- Executing CheckGroup("Local/9xxxxx at Line-optimize-f8c8,2", "1") 
>> in new stack
>>    -- Executing NoOp("Local/9xxxxx at Line-optimize-f8c8,2", "Line 106") 
>> in new stack
>>    -- Executing Dial("Local/9xxxxxx at Line-optimize-f8c8,2", 
>> "SIP/xxxxx at sip-13") in new stack
>>    -- Called xxxxx at sip-13
>>
>> so far so good!
>>
>>    -- Executing SetGroup("SIP/615-92c3", "sip-13") in new stack
>>    -- Executing CheckGroup("SIP/615-92c3", "1") in new stack
>>    -- Executing NoOp("SIP/615-92c3", "Line 106") in new stack
>>    -- Executing Dial("SIP/615-92c3", "SIP/yyyyyyy at sip-13") in new stack
>>    -- Called yyyyyyyyy at sip-13
>>
>> Ahh, it does not check Group counter sip-13, ... it checks 
>> SIP/615-92c3 and Local/9xxxxx at Line-optimize-f8c8,2
>>
>> How can I make it that it checks exactly the Group counter    sip-13  
>> ????
>>
>>
>>
>> bye
>>
>> Ronald
>>
>>
>>
>> _______________________________________________
>> Asterisk-Users mailing list
>> Asterisk-Users at lists.digium.com
>> http://lists.digium.com/mailman/listinfo/asterisk-users
>> To UNSUBSCRIBE or update options visit:
>>   http://lists.digium.com/mailman/listinfo/asterisk-users
>>
>>
>>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
>


-- 
Ronald Wiplinger  (CEO of ELMIT)
http://www.elmit.com    +886 (0) 939--77-55-16  or FWD 511208
- I'm a SpamCon Foundation Member, #694, Verify it at http://www.spamcon.org

PS: Spam prevention!
Our system is protected with a spam prevention program. 
If you send us an e-mail, our system will send you a confirmation message back. Just reply to this confirmation message please. 
After receiving this confirmation message, our system will send the hold message (one) and all future messages (after the received confirmation message) to me without asking you again.