[Asterisk-Users] Setgroup & Checkgroup

[Ronald Wiplinger]

I have some troubles to use Setgroup / Checkgroup!!!

I setup a test (NoOP's are deleted): First caller should get first line, 
second caller should get second line, third caller should get busy and 
send an email. Note, that I used twice here to check the first line!!!



[trunkint_A]

exten => _90NZZZZ.,104,SetGroup(sip-13)        ; increase Group counter
exten => _90NZZZZ.,105,CheckGroup(1)            ; check no more than 1 
in this group
exten => _90NZZZZ.,106,NoOp(Line 106)
exten => _90NZZZZ.,107,Dial(SIP/${EXTEN:${TRUNKMSD}}@sip-13)
exten => _90NZZZZ.,108,hangup
;
exten => _90NZZZZ.,206,SetGroup(sip-12)
exten => _90NZZZZ.,207,CheckGroup(1)
exten => _90NZZZZ.,208,NoOp(Line 208)
exten => _90NZZZZ.,209,Dial(SIP/${EXTEN:${TRUNKMSD}}@sip-12)
exten => _90NZZZZ.,210,hangup
;
exten => _90NZZZZ.,308,SetGroup(sip-13)
exten => _90NZZZZ.,309,CheckGroup(1)
exten => _90NZZZZ.,310,NoOp(Line 310)
exten => _90NZZZZ.,311,Dial(SIP/${EXTEN:${TRUNKMSD}}@sip-13)
exten => _90NZZZZ.,312,hangup
;
exten => _90NZZZZ.,410,Busy
exten => _90NZZZZ.,411,SYSTEM(mail -s 'VPBX all lines in use' 
ronald at elmit.com)


I thought that 104 will set the Group counter "sip-13" to "1" and will 
use line 107 for the dial command
If another caller comes in that way, "sip-13" would be "2" and because 
Checkgroup allows only "1", the Group coutner would be setback to "1" 
and it will follow the jump to 206 and sets the Group counter "sip-12" 
to "1"
A third call should now find Group counter sip-12 and sip-13 set to "1" 
and give a busy signal and send an email.


HOWEVER, the log file show:
    -- Executing SetGroup("Local/9xxxxx at Line-optimize-f8c8,2", "sip-13") 
in new stack
    -- Executing CheckGroup("Local/9xxxxx at Line-optimize-f8c8,2", "1") in 
new stack
    -- Executing NoOp("Local/9xxxxx at Line-optimize-f8c8,2", "Line 106") 
in new stack
    -- Executing Dial("Local/9xxxxxx at Line-optimize-f8c8,2", 
"SIP/xxxxx at sip-13") in new stack
    -- Called xxxxx at sip-13

so far so good!

    -- Executing SetGroup("SIP/615-92c3", "sip-13") in new stack
    -- Executing CheckGroup("SIP/615-92c3", "1") in new stack
    -- Executing NoOp("SIP/615-92c3", "Line 106") in new stack
    -- Executing Dial("SIP/615-92c3", "SIP/yyyyyyy at sip-13") in new stack
    -- Called yyyyyyyyy at sip-13

Ahh, it does not check Group counter sip-13, ... it checks SIP/615-92c3 
and Local/9xxxxx at Line-optimize-f8c8,2

How can I make it that it checks exactly the Group counter    sip-13  ????



bye

Ronald