[Asterisk-Users] 7960 switch port / vlan issue

[lists]

All of the bit buckets and queues are set when you do "auto qos voip
cisco-phone" it sets all of the QOS up for you unless you want to change the
QOS lvls your self which is easy to do but just a royal pain to type in and
keep straight in your in-house Docs.

Doug Block
Chief Information Officer of Efast Funding
713-983-4055 (Direct)
888-338-3863 x 4055 (Toll Free)
713-983-4555 (Direct Fax)
832-483-4495 (Cell)


-----Original Message-----
From: asterisk-users-admin at lists.digium.com
[mailto:asterisk-users-admin at lists.digium.com] On Behalf Of Joseph
Sent: Friday, June 11, 2004 9:59 AM
To: asterisk-users at lists.digium.com
Subject: RE: [Asterisk-Users] 7960 switch port / vlan issue


Thank you very much, I will try that.

I don't know what the wrr stuff is but I will do a little google on it.

This might be a nice addon for the wiki as well.


On Fri, 2004-06-11 at 09:48, lists wrote:
> This direcly from my 3550-24pwr switch
> Once you do auto qos voip cisco-phone the below wrr-queue will all be 
> build
> My data is on vlan 1 but you can add a switchport access vlan XX for
another
> vlan for data
> 
> Hope this helps
> 
> 
> interface FastEthernet0/2
>  switchport trunk encapsulation dot1q
>  switchport voice vlan 66
>  no ip address
>  mls qos trust device cisco-phone
>  mls qos trust cos
>  auto qos voip cisco-phone
>  wrr-queue bandwidth 20 1 80 0
>  wrr-queue min-reserve 1 5
>  wrr-queue min-reserve 2 6
>  wrr-queue min-reserve 3 7
>  wrr-queue min-reserve 4 8
>  wrr-queue cos-map 1 0 1 2 4
>  wrr-queue cos-map 3 3 6 7
>  wrr-queue cos-map 4 5
>  priority-queue out
>  spanning-tree portfast
> 
> Doug Block
> Chief Information Officer of Efast Funding
> 713-983-4055 (Direct)
> 888-338-3863 x 4055 (Toll Free)
> 
> -----Original Message-----
> From: asterisk-users-admin at lists.digium.com
> [mailto:asterisk-users-admin at lists.digium.com] On Behalf Of Joseph
> Sent: Friday, June 11, 2004 4:48 AM
> To: asterisk-users at lists.digium.com
> Subject: [Asterisk-Users] 7960 switch port / vlan issue
> 
> 
> Using a cisco switch with PoE and a cisco 7960 phone:
> 
> In setting up some test setups, I would like to make the 7960 phone 
> work
> in line with the pc
> or as a switch allowing the pc and phone to work on the same cable.
> 
> Assuming I wanted to make the pc use vlan10 and the phone vlan15, does
> anyone have an example of
> how to set this up?
> 
> Here is my attempt in the IOS:
> 
> interface FastEthernet0/10
>  switchport access vlan 10
>  switchport voice vlan 15
> 
> The pc part worked fine but the phone could not seem to pull an ip. 
> Removing the voice part and the pc data cable with just the access 
> vlan statement it works fine on the access vlan.
> 
> J.
> 
> 
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com 
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
> 
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com 
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
-- 
respectfully, Joseph - (606) 477-2355 x140
                       ------=============

_______________________________________________
Asterisk-Users mailing list
Asterisk-Users at lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users