[Asterisk-Users] TE410P PINS

[Wolfgang Pichler]

hi,

Am Fr, den 02.07.2004 schrieb Scott Stingel um 15:31:
> Hi-
> 
> Only pins 1-2 and 4-5 are used, so one of the two cables should work.
> (probably the straight through cable)
ok
> 
> On your zaptel, you should use the phone company as the source for
> asterisk's internal clock, like:
why 1 ? - the documention says that 0 means for the card to take the
timing from its peer (but now i've tryied 1)

> 
> span=1,1,0,ccs,hdb3,crc4
> (But I don't think this would make a difference on the red alarm).  Also,
> try removing crc4 at the end.
my telco told me that they are using crc4 - also if i remove it - it
does not make any difference
> 
> Did you do the following before starting asterisk?
yep - i did so
> 
> modprobe -v wct4xxp 
> sleep 2
> ztcfg -vv
> 
> When you do these commands, is there an error?
> 
> Also, in your /etc/asterisk/zapata, did you specify: signalling=pri_cpe ?
i have signalling=pri_cpi and euroisdn

i have really already tryied everything (i've also checked the card with
a loop cable - works / and i've already tested the other peer - is also
working) - so, what they f... could else be wrong ?

> 
> Regards
> Scott Stingel
> 
> 
> 
> 
> Scott M. Stingel
> President,
> Emerging Voice Technology, Inc.
> Palo Alto California & London England
> www.evtmedia.com
> 
> -----Original Message-----
> From: asterisk-users-admin at lists.digium.com
> [mailto:asterisk-users-admin at lists.digium.com] On Behalf Of Wolfgang Pichler
> Sent: Friday, July 02, 2004 4:42 AM
> To: Asterisk-Users Mailinglist
> Subject: [Asterisk-Users] TE410P PINS
> 
> hi all,
> 
> i am getting crazy with my TE410P - it won't work
> 
> now we already think that the only thing which can be wrong is the cable.
> At our telecom endpoint we have 1-2 tx, 4-5 rx So - which cable do i need to
> get it working
> 
> Already tried a cross over cable 1-2 -> 4-5 / 4-5 -> 1-2 (with this cable
> nothing works -> red alarm on both ends) Also a normal cable 1-2 -> 1-2 /
> 4-5 -> 4-5 (with this cable the telecom endpoint gets a signal - but it
> seems to be the wrong coding/framing - but the TE410P is still on red alarm)
> 
> so, could it be that it will need a: 4-5 -> 4-5, 1-2 -> 7-8 ? (never heard
> about something like this)
> 
> my zaptel.conf is:
> ----------------------------
> span=1,0,0,ccs,hdb3,crc4
> bchan=1-15,17-31
> dchan=16
> 
> loadzone=at
> defaultzone=at
> ----------------------------
> as you can see i am located in austria - my telco is telekom Austria
> 
> thanks for any help
> 
> best regards
> Wolfi
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
> 
> 
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users