[Asterisk-Users] Zaptel BRI and HFC-S cards in NT-Mode

[Klaus-Peter Junghanns]

Hi Ernst,

use this:
exten => 74341423,1,Dial(Zap/g2/74341423,r)
instead of:
exten => 74341423,1,Dial(Zap/5/74341423,r)

-- 
best regards

Klaus
--
Klaus-Peter Junghanns

CEO, CTO
Junghanns.NET GmbH
Breite Straße 13 - 12167 Berlin - Germany
fon: (de) +49 30 79705390
fon: (uk) +44 870 1244692
fax: (de) +49 30 79705391
iaxtel: 1-700-157-8753
http://www.Junghanns.NET/asterisk/



Am Do, 2004-02-19 um 14.24 schrieb Ernst Lehmann:
> Hi, 
> 
> Does anyone operate Asterisk with zaphfc in NT-Mode successfully ??
> 
> I have the problem, that I could not contact my ISDN-Phone on such a
> channel. It rings, but If I pick up the phone, I only get a Hangup in
> the console....
> 
> Thanks for any clues on it...
> 
> Here my setup:
> 
> 3 HFC Cards.
> 
> first card is TE, other two are NT mode (loaded zaphfc with modes=6)
> 
> The ISDN-Phone is connected to the second-card. The ISDN-Bus is powerd
> by an old NTBA like described in the pbx4linux project Howto.
> 
> /etc/zaptel.cfg
> 
> ------------
> span=1,1,3,ccs,ami
> bchan=1-2
> dchan=3
> span=2,0,3,ccs,ami
> bchan=4-5
> dchan=6
> span=3,0,3,ccs,ami
> bchan=7-8
> dchan=9
> -----------
> 
> /etc/asterisk/zapata.conf
> 
> ---------
> switchtype = euroisdn
> signalling = bri_cpe_ptmp
> pridialplan=unknown
> echocancel=yes
> immediate=no
> group = 1
> context=prod
> channel => 1-2
> 
> switchtype = euroisdn
> signalling = bri_net_ptmp
> pridialplan=unknown
> group = 2
> context=prod
> channel => 4-5
> -----------------
> 
> valid passage from extension.conf
> 
> ------------------
> [prod]
> ....
> 
> exten => 74341423,1,Dial(Zap/5/74341423,r)
> 
> .....
> 
> -------------------
> 
> The ISDN-Phone is configured to listen on the MSN 74341423
> 
> Here the log from the console:
> 
> -----------
> 
>     -- Executing Dial("Zap/2-1", "Zap/5/74341423|r") in new stack
>     -- Called 5/74341423
>     -- Hungup 'Zap/5-1'
>     -- Accepting call from '8974341421' to '74341423' on channel 2, span
> 1
> MFE for TEI = 64
>     -- Timeout on Zap/2-1
>   == CDR updated on Zap/2-1
>     -- Executing Goto("Zap/2-1", "#|1") in new stack
>     -- Goto (prod,#,1)
>     -- Sent into invalid extension '#' in context 'prod' on Zap/2-1
>     -- Executing SetVar("Zap/2-1", "starttime=1077196512") in new stack
>     -- Executing Playtones("Zap/2-1", "info") in new stack
>     -- Executing Wait("Zap/2-1", "1") in new stack
>     -- Executing Playback("Zap/2-1", "invalid") in new stack
>     -- Playing 'invalid' (language 'en')
>     -- Executing Wait("Zap/2-1", "1") in new stack
>     -- Executing GotoIf("Zap/2-1", "1?2:7") in new stack
>     -- Goto (prod,i,2)
>     -- Executing Playtones("Zap/2-1", "info") in new stack
>     -- Executing Wait("Zap/2-1", "1") in new stack
>     -- Executing Playback("Zap/2-1", "invalid") in new stack
>     -- Playing 'invalid' (language 'en')
>     -- Channel 2, span 1 got hangup
>   == Spawn extension (prod, i, 4) exited non-zero on 'Zap/2-1'
>     -- Hungup 'Zap/2-1'
> 
> -----------------
> 
> perhaps helpfull... some information from dmesg on loading of modules:
> 
> -------------
> Zapata Telephony Interface Registered on major 196
> zaphfc: start
> PCI: Found IRQ 5 for device 00:09.0
> PCI: Sharing IRQ 5 with 00:04.3
> zaphfc: card configured at mem 0xc8875000 fifo 0xc70e8000(0x70e8000) IRQ
> 5 HZ 10
> 0
> zaphfc: ZTHFC1/0/1
> zaphfc: ZTHFC1/0/2
> zaphfc: ZTHFC1/0/3
> zaphfc: registered zaptel device!
> zaphfc: Card 0 configured for TE mode
> zaphfc: resetting card.
> zaphfc: layer 1 state = F4
> PCI: Found IRQ 12 for device 00:0a.0
> zaphfc: card configured at mem 0xc8877000 fifo 0xc7158000(0x7158000) IRQ
> 12 HZ 1
> 00
> zaphfc: ZTHFC2/0/1
> zaphfc: ZTHFC2/0/2
> zaphfc: ZTHFC2/0/3
> zaphfc: registered zaptel device!
> zaphfc: Card 1 configured for NT mode
> zaphfc: resetting card.
> zaphfc: layer 1 state = F5
> zaphfc: layer 1 state = F6
> zaphfc: layer 1 state = G2
> PCI: Found IRQ 10 for device 00:0b.0
> PCI: Sharing IRQ 10 with 00:11.0
> zaphfc: card configured at mem 0xc8879000 fifo 0xc7148000(0x7148000) IRQ
> 10 HZ 1
> 00
> zaphfc: ZTHFC3/0/1
> zaphfc: ZTHFC3/0/2
> zaphfc: ZTHFC3/0/3
> zaphfc: registered zaptel device!
> zaphfc: Card 2 configured for NT mode
> zaphfc: resetting card.
> zaphfc: bchan rx fifo not enough bytes to receive! (z1=518, z2=8191)
> zaphfc: bchan rx fifo not enough bytes to receive! (z1=518, z2=8191)
> zaphfc: 3 card(s) in this box.
> Registered tone zone 3 (Netherlands)
> zaphfc: layer 1 state = G3
> 
> -----------------------