[Asterisk-Users] Adtran 750 Configuration

[John Baker]

Thanks!

My first 4 POTS lines inbound have caller ID.  I want to make sure it's
passed on to my sip phones.  The internal sip to sip works already for
caller ID, so I'm guessing that enabling caller ID in zapata.conf should
work.

We'll find out.  Thanks again for your help!

John


On Wed, 2004-02-04 at 13:59, Brent Franks wrote:
> Hey John, See my Responses below:
>  
> > Basically, I'm trying to run 10 POTS lines into the Adtran and get
> > output into the T100P.  Clearly, I have very little idea of what I'm
> > doing, so I thought I'd ask:
> 
> Was in the same position two weeks ago, but have a working system now
> tahnks to all the help on the list and the folks at Digium.
> 
> > 1) Do I need to do anything other than put the FXO cards in and figure
> > out which lines are live on the 66 block?  Or will I need to open up a
> > console on the Adtran and fix up a few things?
> 
> Yes, you'll need to figure out on the 66 block which lines go where.  In
> order to integrate with the current 66 block (and provide a fail over so
> the clients could "easily" switch back to the old PBX) I created my own
> AMP 50 cable based on what was coming out of the 66 block, mapped to
> where the FXO cards were.  If retaining an easy way to revert back isn't
> important, you can move the lines around on the 66..?
>  
> > 2) If the latter, what needs to be set on the Adtran?
> 
> You shouldn't really need to setup anything on the Adtran, as it ships
> with the framing we'll use.  I'll describe in the next question.  Also,
> the Adtran 750 ships with a txgain and rxgain of 0 on the FXO cards, so
> there is not much adjustment there that you can do.
>  
> > 3) What are the settings for zaptel.conf and zapata.conf?
> 
> You'll notice the options esf and b8zs below.  The adtran (and almost
> all Chan Banks) ship standard with this.
> 
> The fxsks declaration below describes what channels on the Chan Bank are
> configured.  For FXO ports, you want to use fxsks signaling.
> 
> The loadzone and default zone will obviously be different if you are not
> in the US.
> 
> /etc/zaptel.conf
> 
> span=1,0,0,esf,b8zs
> fxsks=1-5
> # BMZ has the option to add more cards / lines to the CB
> # Setup T1 Span 2
> # span=2,1,0,esf,b8zs
> # fxoks=25-48
> loadzone = us
> defaultzone=us
> 
> 
> The settings described below are pretty straight forward and very well
> documented in the * handbook on asterisk.org under support.  You can
> turn immediate=no to yes if you want, your call.
> 
> /etc/asterisk/zapata.conf
> 
> [channels]
> language=en
> ; Set the context for dialplan calling
> group=1
> context=incoming
> ; FXO Cards use FXS signalling, lets use Kickstart
> signalling=fxs_ks
> ; Don't Use CallerID Because it's not on at BMZ
> usecallerid=no
> ; Cancel that Echo
> echocancel=yes
> ;echocancelwhenbridged=no
> ; Use only the first Channel for Incoming Voice
> callerid = "Incoming" <(###) ###-####>
> immediate=no
> busydetect=no
> callprogress=no
> rxgain=0.0
> txgain=0.0
> channel=1-5
> 
> > 4) How will the caller-ID be signalled?
> 
> Are you talking about Caller ID on internal phones or going out on the
> PSTN?  If you have caller id enabled in Zapata.conf it should be passed
> on to the phone (I have SIP phones, and its passed on)  I don't have
> callerid at this site the config is from, and I send Incoming as the
> callerid string to the incoming phone lines, and then the sip phone
> shows incoming and plays a double trill ring so they no its an external
> incoming.
> 
> > 5) Does anybody need three quad FXS cards?  The Adtran came with 6
> quad
> > FXS and I'm replacing three with FXO cards, so I won't need all of
> > them.  (I was just going to leave the other three in the Adtran)
> >
> > 6) On the other hand, should I take out all 6 FXS cards and just go
> with
> > the three FXO or will it matter?
> 
> If your not going to use FXS I would personally pull them out. Your call
> though, shouldn't make a difference.
>  
> > Thanks in advance,
> > 
> > John Baker
> > List Brokers, Inc.
> > 
> > 
> > _______________________________________________
> > Asterisk-Users mailing list
> > Asterisk-Users at lists.digium.com
> > http://lists.digium.com/mailman/listinfo/asterisk-users
> > To UNSUBSCRIBE or update options visit:
> >    http://lists.digium.com/mailman/listinfo/asterisk-users
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
>