[Asterisk-Users] Hardware opinions?

[Sean Cook]

On Tue, 2004-12-28 at 16:12 -0600, Me wrote:
> Dorn,
> 
>  Can you give me some details on this linux md driver you mentioned?
> 
> Also, you say not to scrap the SATA drives, is this because you think I can
> use them with FC1 or because you think I should try Debian? I really don't
> want to venture away from Fedora at the moment for a few reasons.
> 

FC1 does support SATA drives, however it is dependant upon the sata
controller.  The intel sata driver is supported, adaptec, 3ware 7xxx and
8xxx controllers are also supported. 

> Thanks!
> 
> 
> ----- Original Message ----- 
> From: "Dorn Hetzel" <asterisk-users at dorn.hetzel.org>
> To: "Asterisk Users Mailing List - Non-Commercial Discussion"
> <asterisk-users at lists.digium.com>
> Sent: Tuesday, December 28, 2004 4:07 PM
> Subject: Re: [Asterisk-Users] Hardware opinions?
> 
> 
> > On Tue, Dec 28, 2004 at 02:17:47PM -0600, Me wrote:
> > > Hello, I am trying to build up a pretty meaty Asterisk box after doing
> our initial testing and playing on a 1ghz system.
> > >
> > > Right now I have decided on a prebuilt system which I normally don't do
> but thought it seemed like a good deal.
> > >
> > > I have included the initial specs below, I will be adding another 1 GB
> of RAM for a total of 2 GB.
> > >
> > > My first question is regarding the serial ATA drives... I will be using
> Fedora and considering FC1 seems to be the smartest of the builds when it
> comes to the digium hardware, will I have to scrap the SATA drives because
> FC1 doesn't support them or do I have bad information?
> > >
> > > If I need to scrap the SATA drives and let's say I didn't care about the
> Raid functionality, would you folks think that IDE drives would be fine or
> would the speed of SCSI really make much of a difference when it comes to
> Asterisk? If speed of drives does matter, can someone tell me why Asterisk
> might need fast drives vs. say 7200 IDE drives?
> > >
> > > Next and last question is, how many simultaneous calls do you folks
> figure I can run on this in the following two scenarios:
> > >
> > > 1- All clients would be using SIP devices like SPA-2000's and all calls
> would originate/terminate using an IAX termination partner.
> > > 2- All clients would be using IAX like Asterisk or an IAXy and all calls
> would originate/terminate using an IAX termination partner.
> > >
> > >
> > > Here are the specs:
> > >
> > >   a.. Dual (2) Intel Xeon 2.66GHz CPUs w/ HT Technology
> > >   b.. 533MHz Front Side Bus
> > >   c.. 1GB PC2100 DDR ECC Registered Memory
> > >   d.. Two (2) 120GB SATA 7200RPM Hard Drives with 8MB Cache
> > >   e.. 52X CD-RW Drive w/Burning Software
> > >   f.. 3.5" 1.44MB Floppy Drive
> > >   g.. ATI Rage XL with 8MB Onboard
> > >   h.. Onboard RAID controller
> > >   i.. (2) Intel Ethernet Controllers (1x1000BT Gigabit & 1x10/100)
> > >   j.. 2U Rackmount Chassis w/ 500-Watt Power Supply
> > >
> > > Thanks!
> > >
> >
> > You don't need to scrap the SATA drives, they are very nice.
> > You might want to give Debian a try.
> > Don't use the "RAID" mode on the motherboard as it's likely
> > "fake raid", instead use linux md driver for software raid,
> > it's smoking fast for SATA drives and on my 3.2ghz box
> > barely scratches the CPU resyncing.
> >
> > -Dorn
> >
> > _______________________________________________
> > Asterisk-Users mailing list
> > Asterisk-Users at lists.digium.com
> > http://lists.digium.com/mailman/listinfo/asterisk-users
> > To UNSUBSCRIBE or update options visit:
> >    http://lists.digium.com/mailman/listinfo/asterisk-users
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users