[Asterisk-Users] Fw: [digium.com #12961] T100P as bandwidth

[Matthew Boehm]

What I am confused about the most is this section in /etc/zaptel.conf:

# Next come the dynamic span definitions, in the form:
# dynamic=<driver>,<address>,<numchans>,<timing>
#
# Where <driver> is the name of the driver (e.g. eth), <address> is the
# driver specific address (like a MAC for eth), <numchans> is the number
# of channels, and <timing> is a timing priority, like for a normal span.
# use "0" to not use this as a timing source, or prioritize them as
# primary, secondard, etc.  Note that you MUST have a REAL zaptel device
# if you are not using external timing.
#
# dynamic=eth,eth0/00:02:b3:35:43:9c,24,0

The wiki doesn't say anything about this dynamic stuff. Any clues out there?
Or can I just ignore it?

Thanks,
Matthew

----- Original Message ----- 
From: "Listas" <listas_ast at reliable.com.ar>
To: "Asterisk Users Mailing List - Non-Commercial Discussion"
<asterisk-users at lists.digium.com>
Sent: Thursday, December 23, 2004 10:37 AM
Subject: Re: [Asterisk-Users] Fw: [digium.com #12961] T100P as bandwidth


> I tried to configure a TE110XP using HDLC (mainly to see if it worked) I
> called the guys at Digium because HDLC support is not natively compiled,
> they told me that HDLC was not covered in the free support provided with
the
> card, I had to rebuildl the kernel but as I had not that much time
available
> to play with the Cisco swith which was the E1 connection I had to end the
> test there, however there is some info in:
>
>
http://www.voip-info.org/tiki-index.php?page=Asterisk%20Data%20Configuration
>
> I also read some of the posts in the lists like
> http://lists.digium.com/pipermail/asterisk-users/2004-May/047704.html
>
> http://lists.digium.com/pipermail/asterisk-dev/2003-May/000545.html
>
> hope this helps...
>
> bye,
> M.
> ----- Original Message ----- 
> From: "Matthew Boehm" <mboehm at cytelcom.com>
> To: <asterisk-users at lists.digium.com>
> Sent: Thursday, December 23, 2004 12:37 PM
> Subject: [Asterisk-Users] Fw: [digium.com #12961] T100P as bandwidth
>
>
> > Even though they make the cards and advertise that they support data
> modes,
> > digium won't support data mode on the $500 card they sold to me, so I
must
> > turn to the list.
> >
> > Has anyone configured a T100P to use a T1 strictly as bandwidth? Is
there
> a
> > HOWTO somewhere? Wiki has nothing I could find. I've got plently of
public
> > IPs I can assign to it but don't know how.
> >
> > Thanks,
> > Matthew
> >
> > ----- Original Message ----- 
> > From: "Matthew A. Nicholson via RT" <support at digium.com>
> > To: <mboehm at cytelcom.com>
> > Sent: Thursday, December 23, 2004 10:38 AM
> > Subject: [digium.com #12961] T100P as bandwidth
> >
> >
> > > Yes the hardware, and our drivers suppport both voice and data modes,
> > > but because of the nature of the configuration we do not support it.
> > > Configuring one of our T1 cards for data mode often requires a kernel
> > > recompile, and extensive network device configuration.  Here at Digium
> > > our speciality is telephony not networking, this is why we do not
> > > support the data mode of our hardware.
> > >
> > > > [mboehm at cytelcom.com - Wed Dec 22 17:16:29 2004]:
> > > >
> > > > I dont mean to sound like a jerk but it says quite clearly on your
> > website
> > > > (http://www.digium.com/index.php?menu=wildcard_t100p) that this card
> > does
> > > > both Voice and Data. Why would you guys tell me that the card
supports
> > > data
> > > > but not support data config yourself? They are your cards right?
> > > >
> > > > Thanks,
> > > > Matthew
> > > >
> > >
> > > -- 
> > > Matthew A. Nicholson
> > > Digium
> >
> > _______________________________________________
> > Asterisk-Users mailing list
> > Asterisk-Users at lists.digium.com
> > http://lists.digium.com/mailman/listinfo/asterisk-users
> > To UNSUBSCRIBE or update options visit:
> >    http://lists.digium.com/mailman/listinfo/asterisk-users
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users