[Asterisk-Users] Asterisk 1.0.3 - Signaling on E100P.

[Rich Adamson]

Had the same problem recently with the same cards. Change the order
of the definitions in /etc/zaptel.conf so as to define the E100P
channels first and the TDM channels after. (Someone told me that was
because of the load order of the supporting modules. But in playing
around with those, it didn't make any difference that I could tell.
Ended up having to change the definitions as stated above.)

------------------------
> Hello list ,
> 
> I´m putting to work a new asterisk box.
> I´m running * 1.0.3 with (one )
> Wildcard TDM ( 2FXS* 2FXO) and
> (one) E-100P.
> 
> Both boards are working well. ztcfg
> don´t show me any error.
> zttool list both cards as "OK"
> 
> But when i run asterisk on verbose mode
> i get those errors :
> 
>  [chan_zap.so] => (Zapata Telephony)
>   == Parsing '/etc/asterisk/zapata.conf': Found
>     -- Registered channel 1, FXO Kewlstart signalling
>     -- Registered channel 2, FXO Kewlstart signalling
>     -- Registered channel 3, FXS Kewlstart signalling
>     -- Registered channel 4, FXS Kewlstart signalling
> Dec 11 13:27:48 ERROR[1555]: chan_zap.c:9422 setup_zap: Unknown 
> signalling method 'pri_net'
> Dec 11 13:27:48 ERROR[1555]: chan_zap.c:6209 mkintf: Signalling 
> requested is FXS Kewlstart but line is in PRI Signalling signalling
> Dec 11 13:27:48 ERROR[1555]: chan_zap.c:9141 setup_zap: Unable to 
> register channel '5-19'
> Dec 11 13:27:48 WARNING[1555]: loader.c:345 ast_load_resource: 
> chan_zap.so: load_module failed, returning -1
>   == Unregistered channel type 'Tor'
>   == Unregistered channel type 'Zap'
>     -- Unregistered channel 1
>     -- Unregistered channel 2
>     -- Unregistered channel 3
>     -- Unregistered channel 4
> Dec 11 13:27:48 WARNING[1555]: loader.c:440 load_modules: Loading module 
> chan_zap.so failed!
> 
> --- My zaptel.conf ---
> 
> # configuracoes para o zaptel
> # placa TDM c/ 2 FXs e 2 Fxo
> 
> fxoks=1-2
> fxsks=3-4
> 
> # Placa E100 / E1 - 30 canais de voz (FXO )
> 
> span=1,1,0,ccs,hdb3
> bchan=5-19
> dchan=20
> bchan=21-35
> defaultzone=br
> loadzone=br
> 
> --- My Zapata.conf --
> 
> [channels]
> 
> ; As configuracoes abaixo fazem referencia a
> ; placa Wildcard TDM com 2 canais FXS w
> ; 2 canais FXO
> 
> signalling=fxo_ks
> echocancel=128 ; You can set this to 32, 64, or 128, tweak to your needs.
> echocancelwhenbridged=yes
> echotraining=800 ; Asterisk trains to the beginning of the call, number 
> is in milliseconds
> callerid=asreceived
> group=1
> context=fxs ; Points to the default context of your extensions.conf
> channel => 1-2
> 
> signalling=fxs_ks
> ;callerid=asreceived
> echocancel=128 ; You can set this to 32, 64, or 128, tweak to your needs.
> echocancelwhenbridged=yes
> echotraining=800 ; Asterisk trains to the beginning of the call, number 
> is in milliseconds
> group=2
> context=incoming
> channel=> 3-4 ; Again if you only have one FXO module remove the '-4'
> 
> ;
> ;
> ;
> ;
> ; As Configuracoes abaixo se referem a placa E1
> ; que disponibiliza 30 canais FXO
> 
> ;group=3
> switchtype=euroisdn
> ;signalling=pri_net
> ;context=incoming
> ;channel=> 5-19,21-35
> ;channel=> 21-35
> 
> Any ideas ::: ???????????
> 
> Best Regards ,
> 
> -Jefferson Carvalho
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users

---------------End of Original Message-----------------