[Asterisk-Users] determining what number was dialed?

[Chris Shaw]

Except for what you said about 1-800 numbers pointing to the same line...
nevermind I'll shut up now...

    -Chris

----- Original Message -----
From: "Chris Shaw" <chriss at watertech.com>
To: <asterisk-users at lists.digium.com>
Sent: Friday, August 20, 2004 1:47 PM
Subject: Re: [Asterisk-Users] determining what number was dialed?


> True, very true... If it's PRI then you will get DNIS/DNID from the
> D-Channel...
>
> If they're doing anything other than PRI though, like a regular T1 into a
> channel bank (or into a TE100P or TE40xP) , this would work... Lines would
> be assigned to a specific channel and they could be separated out with
> contexts... Not as pretty as using DNIS but it would work...
>
> -Chris
>
> ----- Original Message -----
> From: "Steven Critchfield" <critch at basesys.com>
> To: <asterisk-users at lists.digium.com>
> Sent: Friday, August 20, 2004 1:29 PM
> Subject: Re: [Asterisk-Users] determining what number was dialed?
>
>
> > On Fri, 2004-08-20 at 15:23, Chris Shaw wrote:
> > > Why not use separate contexts for these lines in zapata.conf? Seems
way
> > > simpler to me...
> > >
> > > http://www.voip-info.org/wiki-Asterisk+config+zapata.conf
> >
> > Who said they are seperate lines. 1-800 numbers can just be redirects to
> > other lines. In that case you have to have a different signaling method
> > to determine 1800-a on line b is different from 1800-c on line b.
> >
> > In a PRI circuit, the "lines" are just channels, all signaling data is
> > run over the D channel and any "line" can be any number routed to that
> > circuit.
> >
> >
> > > ----- Original Message -----
> > > From: "Steven Critchfield" <critch at basesys.com>
> > > To: <asterisk-users at lists.digium.com>
> > > Sent: Friday, August 20, 2004 12:33 PM
> > > Subject: Re: [Asterisk-Users] determining what number was dialed?
> > >
> > >
> > > > On Fri, 2004-08-20 at 14:28, Paul Concepcion wrote:
> > > > > Hey all,
> > > > >
> > > > > I've setup * to serve the needs of our small helpdesk and I'm
> looking
> > > > > to expand. We're planning on doing support for different
companies,
> > > > > each one identified by a different 1-800 number that terminates at
> our
> > > > > PBX. What I would like to know is: is there a variable I can read
to
> > > > > determine what number any given caller dialed? I'd like to be able
> to
> > > > > separate calls based on who called 1-800-777-7777 and who dialed
> > > > > 1-800-555-5555, for example.
> > > >
> > > > Yes, but it depends on what type of telephony signalling you are
using
> > > > as to whether or not you can get that information.
> > > >
> > > > Tells us about your PSTN connection.
> > > > --
> > > > Steven Critchfield <critch at basesys.com>
> >
> >
> > _______________________________________________
> > Asterisk-Users mailing list
> > Asterisk-Users at lists.digium.com
> > http://lists.digium.com/mailman/listinfo/asterisk-users
> > To UNSUBSCRIBE or update options visit:
> >    http://lists.digium.com/mailman/listinfo/asterisk-users
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users