[Asterisk-Users] TE405P + Adit 600 and FXO module - should this work?

[Darren Nickerson]

Thanks! I'll spend some time with this information, check the pinouts and I
should be well on my way. Glad to know it can work! ;-)

-Darren

-- 
Darren Nickerson
Senior Sales & Support Engineer
iFAX Solutions, Inc. www.ifax.com
darren.nickerson at ifax.com
+1.215.438.4638 ext 8106 office
+1.215.243.8335 fax

----- Original Message ----- 
From: "Darren Nickerson" <darren.nickerson at ifax.com>
To: <asterisk-users at lists.digium.com>
Sent: Friday, April 16, 2004 1:29 AM
Subject: [Asterisk-Users] TE405P + Adit 600 and FXO module - should this
work?


> Folks,
>
> I'm experimenting with bringing multiple (8) analog lines from our local
> telco into a Carrier Access ADIT 600 channel bank with an FXO module, then
> having this talk to Asterisk via the T1 TDM controller on the ADIT and a
> TE405P card.
>
> I don't know if this will work well (ie: give me decent echo cancellation,
> call disconnect supervision, caller ID etc) but I haven't had much luck
> getting this combination flying at all thus far. Should it work?
>
> I've been concentrating on the Adit T1 interface <----> TE405P connection
> ... and have the following in zapata.conf:
>
>    span=1,1,0,esf,b8zs
>    fxsks=1-24
>    loadzone = us
>    defaultzone=us
>
> At the end of my zaptel.conf, I have:
>
>    signalling=fxs_ks
>    group=2
>    callerid="Joe Schmoe" <(215) 555-1212>
>    channel => 1-24
>
> To get things flying, I do:
>
>    modprobe zaptel
>    modprobe wct4xxp
>
> which causes the TE405P card to activate, but show a single flashing red
> alarm on the configured span.
>
> The Adit's TDM controller also displays a solid red LED. Here's its
status:
>
>    Adit 600> status a:1
>    SLOT A:
>    Status for DS1  1:
>        Receive:                 Loss of Signal
>        Transmit:                RAI/Yellow Alarm
>        Loopback:                OFF
>
>    Adit 600>
>
> I'm not sure I have the DS1 configured appropriately. It says:
>
>    Adit 600> show a:1
>    SLOT A:
>    Settings for DS1  1:
>        Circuit ID:              CAC DS1# A:1
>        Up/Down:                 UP
>        Framing:                 ESF
>        Line Coding:             B8ZS
>        Line Build Out:          DSX-1 EQUALIZATION FOR 0-133 ft. (CSU 0dB)
>        Loop Code Detection:     ON
>        Loopback:                OFF
>        FDL Type:                None
>
> Can anyone familiar with the Adit 600 and/or TE405P see any obvious errors
> here?
>
> -Darren
>
> -- 
> Darren Nickerson
> Senior Sales & Support Engineer
> iFAX Solutions, Inc. www.ifax.com
> darren.nickerson at ifax.com
> +1.215.438.4638 ext 8106 office
> +1.215.243.8335 fax
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
>