[Asterisk-Users] quadBRI card installation issues

[Robinson Tim-W10277]

Use RC16.  This seems to solve our issues on a UK ISDN2e line.

Rgds
Tim

-----Original Message-----
From: asterisk-users-admin at lists.digium.com [mailto:asterisk-users-admin at lists.digium.com] On Behalf Of Julien Levi
Sent: 02 April 2004 01:17
To: asterisk-users at lists.digium.com
Cc: Jens-Uwe Junghanns
Subject: [Asterisk-Users] quadBRI card installation issues


Hi there,

I am attempting to set up a simple BRI and SIP based platform using * 
with the quadbri card (it's not sharing an IRQ). I enclose my zaptel and 
zapata.conf files. For the inital test I'm simply trying to connect to 
the * demo menu.

The drivers compile (with a few warning that I believe aren't important 
- see attachments). chan_zap comiles with the warning:

chan_zap.c: In function `pri_dchannel':
chan_zap.c:6344: warning: passing arg 1 of `pbx_builtin_setvar_helper' 
from incompatible pointer type

The qozap driver appears to load correctly and I get this in the log :

Apr  1 17:51:07 debian kernel: Zapata Telephony Interface Registered on 
major 196
Apr  1 17:51:07 debian kernel: qozap: start
Apr  1 17:51:07 debian kernel: PCI: Enabling device 00:0b.0 (0000 -> 0003) Apr  1 17:51:07 debian kernel: PCI: Found IRQ 10 for device 00:0b.0 Apr  1 17:51:07 debian kernel: qozap: quadBRI card configured at mem 
0xd0888000 IRQ 10 HZ 100 CardID 0
Apr  1 17:51:07 debian kernel: S/T port 1 is in TE mode.
Apr  1 17:51:07 debian kernel: S/T port 2 is in TE mode.
Apr  1 17:51:07 debian kernel: S/T port 3 is in TE mode.
Apr  1 17:51:07 debian kernel: S/T port 4 is in TE mode.
Apr  1 17:51:07 debian kernel: qozap: registered zaptel span 1. Apr  1 17:51:07 debian kernel: qozap: registered zaptel span 2. Apr  1 17:51:07 debian kernel: qozap: registered zaptel span 3. Apr  1 17:51:07 debian kernel: qozap: registered zaptel span 4. Apr  1 17:51:07 debian kernel: card 1 span 1 state F0 (A_ST_RD_STA = 0x0) Apr  1 17:51:07 debian kernel: card 1 span 2 state F0 (A_ST_RD_STA = 0x0) Apr  1 17:51:07 debian kernel: card 1 span 3 state F0 (A_ST_RD_STA = 0x0) Apr  1 17:51:07 debian kernel: card 1 span 4 state F0 (A_ST_RD_STA = 0x0) Apr  1 17:51:07 debian kernel: qoztmp->cardno = 1 Apr  1 17:51:07 debian kernel: qozap: 1 multiBRI card(s) in this box, 4 
BRI ports total.
Apr  1 17:51:07 debian kernel: Registered tone zone 4 (United Kingdom) Apr  1 17:51:07 debian kernel: qozap: starting card 1 span 1/0. Apr  1 17:51:07 debian kernel: card 1 span 1 state F6 (A_ST_RD_STA = 0x16) Apr  1 17:51:07 debian kernel: card 1 span 1 state F7 (A_ST_RD_STA = 0x17)

However when running * I get the message below every 2-3 seconds:

Apr  1 18:10:55 WARNING[11276]: PRI: !! Got S-frame while link down

Attempting to call the line does not result in it being answered but I 
get the error:

Apr  1 18:11:23 WARNING[11276]: PRI: !! Got I-frame while link state 0

When the line starts to ring and again when I hang up.

I'm using a bt buisness highway line which is isdn2e comaptible but 
doesn't provide power on the digital socket.

Any suggestions on how to resolve this would be greatly appreciated. I 
can find nothing on this in the list archives (though similar errors 
have been seen using a t410p card under high call load:  
http://lists.digium.com/pipermail/asterisk-users/2004-March/040745.html )

I'm using the bri-stuff rc15 from:

http://www.junghanns.net/asterisk/downloads/bri-stuff-0.0.2rc15.tar.gz

Thanks in advance for any suggestions,

regards,

Julien