[Asterisk-Users] E400P and 2 X100P working, but not together

Sun May 18 15:49:05 MST 2003

This was the point I was trying to prove.  I'm not even 
trying to use the E400P yet.  This is why I didn't 
modprobe the tur2 module.  I was trying to to prove that 
even just uncommenting the lines for the E1 card in 
zaptel.conf, making NO other changes, causes the wcfxo 
module to not work.

Jamie Carl

On Sun, 18 May 2003 02:57:10 -0400
  "Joe Antkowiak" <joe at jsci.net> wrote:
>*This message was transferred with a trial version of 
>CommuniGate(tm) Pro*
>After you modprobe'd wcfxo, did you modprobe for the E1 
>card?
>
>It will do that, I have an x100p, t100p, and a tdm400p on 
>the same box, and
>I have to modprobe in the order of the channel numbers, 
>and I get errors
>like that, but it all works when its done...
>
>-----Original Message-----
>From: asterisk-users-admin at lists.digium.com
>[mailto:asterisk-users-admin at lists.digium.com] On Behalf 
>Of Jamie Carl
>Sent: Sunday, May 18, 2003 2:22 AM
>To: asterisk-users at lists.digium.com
>Subject: RE: [Asterisk-Users] E400P and 2 X100P working, 
>but not together
>
>*This message was transferred with a trial version of 
>CommuniGate(tm) Pro*
>Doesn't seem to work.
>
>With a working config for an X100P, uncomment the 
>following lines in
>zaptel.conf:
>
>span=1,1,0,esf,hdb3,crc4
>dchan=2-33
>
>That's the only changes I have made.  Now when I try to 
>load wcfxo with
>modprobe
>I get an error which you said I may still get:
>
>ZT_SPANCONFIG failed on span 1: Invalid argument (22)
>/lib/modules/2.4.18-14/misc/wcfxo.o: post-install wcfxo 
>failed
>/lib/modules/2.4.18-14/misc/wcfxo.o: insmod wcfxo failed
>
>
>But then, upon loading asterisk I get to following error:
>
>   == Parsing '/etc/asterisk/zapata.conf': Found
>WARNING[8192]: File chan_zap.c, Line 576 (zt_open): 
>Unable to specify
>channel 1:
>  No such device or address
>ERROR[8192]: File chan_zap.c, Line 4727 (mkintf): Unable 
>to open channel
>1: No s
>uch device or address
>here = 0, tmp->channel = 0, channel = 1
>ERROR[8192]: File chan_zap.c, Line 6368 (load_module): 
>Unable to
>register channe
>l '1'
>WARNING[8192]: File loader.c, Line 299 
>(ast_load_resource): chan_zap.so:
>load_mo
>dule failed, returning -1
>WARNING[8192]: File loader.c, Line 394 (load_modules): 
>Loading module
>chan_zap.s
>o failed!
>
>This tells me that the wcfxo module didn't actually pick 
>up the card
>correctly.
>I didn't change anything else (yet) apart from the two 
>lines above, and
>I havn't
>eveb tried to load the tor2 module.  So from what I can 
>gather, having
>lines in
>zaptel.conf that the module doesn't understand seems to 
>prevent it from
>working.
>
>Is this correct?  By design purhaps?  I'm lost as what to 
>try next.
>
>Regards,
>
>Jamie Carl
>Email:	me at jazz-inc.net
>PH:		+61-414-365-466
>
>-----Original Message-----
>From: Steven Critchfield [mailto:critch at basesys.com]
>Sent: Sunday, 18 May 2003 3:48 PM
>To: asterisk-users at lists.digium.com
>Subject: Re: [Asterisk-Users] E400P and 2 X100P working, 
>but not
>together
>
>
>*This message was transferred with a trial version of 
>CommuniGate(tm)
>Pro*
>This all depends on the order you wish to have the 
>channels appear.
>
>I'd say if you don't have a fully deployed E400P, then 
>put it last so as
>to keep the ports all together when you deploy them 
>later. 
>
>So, make your X100P channel 1, and configure it like you 
>had before.
>Then your E400P channels start at channels 2-33. Since 
>you are using 2
>types of drivers, you may see an error after loading the 
>first driver.
>You may even want to run ztcfg after you load the second 
>driver just to
>be sure they all get configed right.  
>
>On Sun, 2003-05-18 at 00:18, Jamie Carl wrote:
>> Hey all,
>>  
>> I'm trying to get an E400P and 2 X100Ps working together 
>>in the one
>> box and don't seem to be having much luck.
>>  
>> I can get the two different types of boards working 
>>separately, but
>> not together.  I've made calls on both the X100P and 
>>have seen sync
>> and correct signalling on the E400P.  But when I try to 
>>enable to
>> configs together I get the following:
>>  
>> modprobe wcfxo produces:
>> ZT_SPANCONFIG failed on span 1: Invalid argument (22)
>> /lib/modules/2.4.18-14/misc/wcfxo.o: post-install wcfxo 
>>failed
>> /lib/modules/2.4.18-14/misc/wcfxo.o: insmod wcfxo failed
>>  
>> and modprobe tor2 produces:
>> ZT_SPANCONFIG failed on span 1: Invalid argument (22)
>> /lib/modules/2.4.18-14/misc/tor2.o: post-install tor2 
>>failed
>> /lib/modules/2.4.18-14/misc/tor2.o: insmod tor2 failed
>>  
>> And nothing works.....
>>  
>> Now if I remove the E1 configs from zaptel.conf the 
>>wcfxo loads, and
>> vice versa.  
>>  
>> Is there a way to get them working together????   Or 
>>will they be
>> mutually exclusive, ie, an asterisk server can only have 
>>ether X100Ps
>> OR E400Ps in it, but not both.
>>  
>> Has anyone else made them work together and is there 
>>something I'm
>> missing?
>> 
>> Thanx all...
>>  
>> 
>> Regards,
>> 
>> Jamie Carl
>> 
>> Email:
>> 
>> me at jazz-inc.net
>> 
>> Phone:
>> 
>> +61 414 365 466
>> 
>> Jabber:
>> 
>> jazz at netmindz.net
>> 
>> 
>> 
>-- 
>Steven Critchfield <critch at basesys.com>
>
>_______________________________________________
>Asterisk-Users mailing list
>Asterisk-Users at lists.digium.com
>http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
>
>_______________________________________________
>Asterisk-Users mailing list
>Asterisk-Users at lists.digium.com
>http://lists.digium.com/mailman/listinfo/asterisk-users
>
>_______________________________________________
>Asterisk-Users mailing list
>Asterisk-Users at lists.digium.com
>http://lists.digium.com/mailman/listinfo/asterisk-users