[Asterisk-Users] ISDN PRI E1 configuration with E100P
surajee at infotechs.lk
surajee at infotechs.lk
Sat Jul 12 04:22:47 MST 2003
hi,
I sorted it out, after removing crc4 in zaptel.conf, the green light came on and i can now take
outgoing calls.
Thank you for all who helped :-)
Surajee
----- Original Message -----
From: <surajee at infotechs.lk>
To: <asterisk-users at lists.digium.com>
Sent: Saturday, July 12, 2003 12:27 PM
Subject: Re: [Asterisk-Users] ISDN PRI E1 configuration with E100P
> here are the outputs,
> for, zttool,
>
> Alarms Span
> RED LSS Wildcard T100P T1/PRI Board card 0
>
>
> for head /proc/zaptel/1
>
> Span 1: WCT1/0 "LSS Wildcard T100P T1/PRI Board card 0" HDB3/CCS/CRC4 RED
> 1 WCT1/0/1 ClearChannel
> 2 WCT1/0/2 ClearChannel
> 3 WCT1/0/3 ClearChannel
> 4 WCT1/0/4 ClearChannel
> 5 WCT1/0/5 ClearChannel
> 6 WCT1/0/6 ClearChannel
> 7 WCT1/0/7 ClearChannel
> 8 WCT1/0/8 ClearChannel
> 9 WCT1/0/9 ClearChannel
>
> any idea?
>
> Surajee
>
> ----- Original Message -----
> From: "Martin Pycko" <martinp at digium.com>
> To: <asterisk-users at lists.digium.com>
> Sent: Saturday, July 12, 2003 12:41 AM
> Subject: Re: [Asterisk-Users] ISDN PRI E1 configuration with E100P
>
>
> > Look in zttool or "head /proc/zaptel/[1-5]
> > to see if the spans are in alarms. The leds on your boards might not lit
> > properly.
> >
> > regards
> > Martin
> >
> > On Fri, 11 Jul 2003 surajee at infotechs.lk wrote:
> >
> > > yes, now i got the that problem solved, with 'immediate=yes', but now i've
> > > faced with another,
> > > When I connect the E1 to the cards, the LED lights does not change to green,
> > > in E100P, its blinking red (even when there is no E1 plugged, its blinking
> > > red)
> > > and in E400P, its solid red. (this was the same even without
> > > 'immediate=yes')
> > >
> > > When i start asterisk, the cards starts fine (as we see), givin the
> > > following output,
> > > *CLI>
> > > == D-Channel on span 1 up
> > > -- B-channel 1 successfully restarted on span 1
> > > -- B-channel 2 successfully restarted on span 1
> > > . . .
> > > -- B-channel 31 successfully restarted on span 1
> > >
> > > after i put 'immediate=yes', i can even call from outside to the PRI E1, and
> > > get connected to asterisk, and listen to the prompts played by asterisk
> > >
> > > -- Accepting call from '062279955' to 's' on channel 1, span 1
> > > -- Executing Wait("Zap/1-1", "2") in new stack
> > > -- Executing Answer("Zap/1-1", "") in new stack
> > > -- Executing DigitTimeout("Zap/1-1", "5") in new stack
> > > -- Set Digit Timeout to 5
> > > -- Executing ResponseTimeout("Zap/1-1", "10") in new stack
> > > -- Set Response Timeout to 10
> > > -- Executing BackGround("Zap/1-1", "demo-congrats") in new stack
> > > -- Playing 'demo-congrats'
> > >
> > > But calling to outside from asterisk fails (with the following errors), we
> > > don't know whether this related to the above problem
> > >
> > > Executing Dial("SIP/802-8a26", "Zap/g2/0129063800|20|t") in new stack
> > > NOTICE[262160]: File app_dial.c, Line 481 (dial_exec): Unable to create
> > > channel of type 'Zap'
> > > == Everyone is busy at this time
> > > -- Executing Congestion("SIP/802-8a26", "") in new stack
> > > == Spawn extension (sip, 980129063800, 2) exited non-zero on
> > > 'SIP/802-8a26'
> > >
> > > Following are new zaptel and zapata conf files,
> > >
> > > zapata.conf
> > >
> > > [channels]
> > > transfer=yes
> > > echocancel=yes
> > > callprogress=yes
> > > immediate=yes
> > >
> > > ;E100p card
> > > switchtype=EuroISDN
> > > signalling=pri_cpe
> > > pridialplan=unknown
> > > context=inbound-pstn
> > > group=2
> > > channel => 1-15,17-31
> > >
> > > zaptel.conf
> > >
> > >
> > > #E100p card
> > > span=1,0,0,ccs,hdb3,crc4
> > > bchan=1-15,17-31
> > > dchan=16
> > >
> > > defaultzone=us
> > > loadzone=us
> > >
> > >
> > > Thank you,
> > >
> > > Surajee
> > >
> > > ----- Original Message -----
> > >
> > > From: "Cristi" <cvasiliu at accessnet.ro>
> > > To: <asterisk-users at lists.digium.com>
> > > Sent: Friday, July 11, 2003 10:39 PM
> > > Subject: Re: [Asterisk-Users] ISDN PRI E1 configuration with E100P
> > >
> > >
> > > > surajee at infotechs.lk wrote:
> > > >
> > > > > hi Everyone,
> > > > >
> > > > > We are configuring an ISDN PRI E1 with an E100P card, when you load
> > > > > the drivers, and starts the asterisk, cards also starts fine, givin
> > > > > following output,
> > > > >
> > > > > *CLI>
> > > > > == D-Channel on span 1 up
> > > > > -- B-channel 1 successfully restarted on span 1
> > > > > -- B-channel 2 successfully restarted on span 1
> > > > > . . .
> > > > > -- B-channel 31 successfully restarted on span 1
> > > > >
> > > > > but, when we make a call to this E1 from outside, it gives the
> > > > > following error,
> > > > >
> > > > > WARNING[213006]: File chan_zap.c, Line 5248 (pri_fixup): Call
> > > > > specified, but not found?
> > > > > WARNING[213006]: File chan_zap.c, Line 5786 (pri_dchannel): Hangup on
> > > > > bad channel 1
> > > > > WARNING[213006]: File chan_zap.c, Line 5248 (pri_fixup): Call
> > > > > specified, but not found?
> > > > > WARNING[213006]: File chan_zap.c, Line 5786 (pri_dchannel): Hangup on
> > > > > bad channel 2
> > > > >
> > > > > does anybody hav an idea on this?
> > > > >
> > > > > our zaptel.conf is,
> > > > >
> > > > > #E100p card
> > > > > span=1,0,0,ccs,hdb3,crc4
> > > > > bchan=1-15,17-31
> > > > > dchan=16
> > > > >
> > > > > zapata.conf,
> > > > >
> > > > > ;E100p card
> > > > > switchtype=EuroISDN
> > > > > signalling=pri_cpe
> > > > > pridialplan=unknown
> > > > > context=incoming
> > > > > group = 2
> > > > > channel => 1-15,17-31
> > > > >
> > > > > Thanks inadvance,
> > > > >
> > > > > Surajee
> > > > >
> > > > >
> > > > > --------------This mail sent through OmniBIS.com--------------
> > > > > _______________________________________________ Asterisk-Users mailing
> > > > > list Asterisk-Users at lists.digium.com
> > > > > http://lists.digium.com/mailman/listinfo/asterisk-users
> > > >
> > > > I was having the same problem because : 1 number for E1 and the local
> > > > PTSN was not sending the DID to select the appropriate extension. Set
> > > > the immediate=yes into zapata.conf and catch the call into s extension!
> > > > Thanks to Martin Pycko ...
> > > >
> > > > _______________________________________________
> > > > Asterisk-Users mailing list
> > > > Asterisk-Users at lists.digium.com
> > > > http://lists.digium.com/mailman/listinfo/asterisk-users
> > > >
> > > >
> > >
> > >
> > > --------------This mail sent through OmniBIS.com--------------
> > >
> > > _______________________________________________
> > > Asterisk-Users mailing list
> > > Asterisk-Users at lists.digium.com
> > > http://lists.digium.com/mailman/listinfo/asterisk-users
> > >
> >
> >
> > _______________________________________________
> > Asterisk-Users mailing list
> > Asterisk-Users at lists.digium.com
> > http://lists.digium.com/mailman/listinfo/asterisk-users
> >
>
> --------------This mail sent through OmniBIS.com--------------
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
--------------This mail sent through OmniBIS.com--------------
More information about the asterisk-users
mailing list