<div dir="ltr">If someone is able to reproduce this behavior (unstable bits after red alarm bouncing) I can take a look, however, if the ABCD bits as reported by the DAHDI driver are the problem, there is nothing openr2 can do as it trusts what DAHDI says<div>
<br></div><div>Moy<br><div><div class="gmail_extra"><br><br><div class="gmail_quote">On Thu, May 9, 2013 at 4:53 PM, Marcelo Pacheco <span dir="ltr"><<a href="mailto:marcelo@m2j.com.br" target="_blank">marcelo@m2j.com.br</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-color:rgb(204,204,204);border-left-style:solid;padding-left:1ex">
<div bgcolor="#FFFFFF" text="#000000">
<div>I have seen this happen when there are
quick alarm on the trunk, OK->RED, 1-4 seconds later,
RED->OK, check for alarms on the log.<br>
If it's this problem, a dahdi restart will rectify.<br>
Let the developers know, I'm trying to get 100% rid of all MFC R2
with Asterisk due to this kind of issues, but ISDN is impossible
to obtain in the countryside.<span class=""><font color="#888888"><br>
<br>
Marcelo</font></span><div><div class="h5"><br>
<br>
On 05/09/13 17:00, ServTelar wrote:<br>
</div></div></div><div><div class="h5">
<blockquote type="cite">
Check the bit status using dahdi_tool. ABCD=1101 means block, 1001
means idle (showing in vertical).
<div><br>
</div>
<div>
<div> ┌───────────────┤ T4XXP (PCI) Card 0 Span 3
├────────────────┐
</div>
<div> ┌─────│
│ ────┐
</div>
<div> │ │
│ │
</div>
<div> │ │
Current Alarms: No alarms. │
│ </div>
<div> │ │
Sync Source: T4XXP (PCI) Card 0 Span 1 │ ↑
│ </div>
<div> │ │
IRQ Misses: 0 │ ▒
│ </div>
<div> │ │
Bipolar Viol: 0 │ ▒
│ </div>
<div> │ │
Tx/Rx Levels: 0/ 0 │ ▒
│ </div>
<div> │ │
Total/Conf/Act: 31/ 30/ 30 │ ▒
│ </div>
<div> │ │
1111111111222222222233
┌──────┐ │ ▒ │
</div>
<div> │ │
1234567890123456789012345678901 │ Back │ │ ▮ │
</div>
<div> │ │
TxA 111111111111111 111111111111111 └──────┘ │ ▒ │
</div>
<div> │ │
TxB 111111111111111 111111111111111 │ ▒
│ </div>
<div> │ │
TxC 000000000000000 000000000000000 │ ↓
│ </div>
<div> │ │
TxD 111111111111111 111111111111111 │
│ </div>
<div> │ │
│ │
</div>
<div> │ │
RxA 111111111111111 111111111111111 │
│ </div>
<div> │ │
RxB 011111111111111 111111111111111 │
│ </div>
<div> │ │
RxC 000000000000000 000000000000000 │
│ </div>
<div> │ │
RxD 111111111111111 111111111111111 </div>
</div>
<div><br>
</div>
<div>In this case just ch=1 is receiving idle, the rest are
blocked, and we're transmitting blocked.</div>
<div><br>
</div>
<div>Regards</div>
<div><br>
</div>
<div>Gustavo</div>
<div><br>
</div>
<div><br>
</div>
<div>
<div>On May 9, 2013, at 3:51 PM, Christian Cabrera <<a href="mailto:ccabrera@gmail.com" target="_blank">ccabrera@gmail.com</a>>
wrote:</div>
<br>
<blockquote type="cite">
<div dir="ltr">
<div style="font-family:tahoma,sans-serif;color:rgb(0,0,102)">Hello,</div>
<div style="font-family:tahoma,sans-serif;color:rgb(0,0,102)"><br>
</div>
<div style="font-family:tahoma,sans-serif;color:rgb(0,0,102)">
Recently, the E1 of one of my clients stopped "almost"
working. They have a 10 channel E1 with R2, but only the
first channel appears as IDLE, while the remaining stay at
BLOCK.</div>
<div style="font-family:tahoma,sans-serif;color:rgb(0,0,102)">
<br>
</div>
<div style="font-family:tahoma,sans-serif;color:rgb(0,0,102)">Here's
what the mfcr2 show channels throws:</div>
<div style="font-family:tahoma,sans-serif;color:rgb(0,0,102)">
<br>
</div>
<div>
<div><font color="#000066" face="tahoma, sans-serif">Chan Variant Max ANI Max
DNIS ANI First Immediate Accept Tx CAS Rx CAS</font></div>
<div>
<font color="#000066" face="tahoma, sans-serif"> 1 MX
10 4 No No IDLE
IDLE</font></div>
<div><font color="#000066" face="tahoma, sans-serif"> 2 MX 10 4
No No IDLE BLOCK</font></div>
<div><font color="#000066" face="tahoma, sans-serif"> 3 MX 10 4
No No IDLE BLOCK</font></div>
<div><font color="#000066" face="tahoma, sans-serif"> 4 MX 10 4
No No IDLE BLOCK</font></div>
<div><font color="#000066" face="tahoma, sans-serif"> 5 MX 10 4
No No IDLE BLOCK</font></div>
<div><font color="#000066" face="tahoma, sans-serif"> 6 MX 10 4
No No IDLE BLOCK</font></div>
<div><font color="#000066" face="tahoma, sans-serif"> 7 MX 10 4
No No IDLE BLOCK</font></div>
<div><font color="#000066" face="tahoma, sans-serif"> 8 MX 10 4
No No IDLE BLOCK</font></div>
<div><font color="#000066" face="tahoma, sans-serif"> 9 MX 10 4
No No IDLE BLOCK</font></div>
<div><font color="#000066" face="tahoma, sans-serif"> 10 MX 10 4
No No IDLE BLOCK</font></div>
<div style="color:rgb(0,0,102);font-family:tahoma,sans-serif"><br>
</div>
<div style="color:rgb(0,0,102);font-family:tahoma,sans-serif"><br>
</div>
<div style="color:rgb(0,0,102);font-family:tahoma,sans-serif">The
configuration is as usual. Here's my system.conf:</div>
<div style="color:rgb(0,0,102);font-family:tahoma,sans-serif"><br>
</div>
<div style="color:rgb(0,0,102);font-family:tahoma,sans-serif">------------------------------------------</div>
<div>
<div><font color="#000066" face="tahoma, sans-serif">span=1,1,0,cas,hdb3</font></div>
<div><span style="color:rgb(0,0,102);font-family:tahoma,sans-serif">cas=1-15:1101</span><br>
</div>
<div><font color="#000066" face="tahoma, sans-serif">cas=17-31:1101</font></div>
<div><span style="color:rgb(0,0,102);font-family:tahoma,sans-serif">echocanceller=mg2,1-15,17-31</span><br>
</div>
<div><br>
</div>
<div><font color="#000066" face="tahoma, sans-serif">loadzone
= mx</font></div>
<div><font color="#000066" face="tahoma, sans-serif">defaultzone
= mx</font></div>
<div style="color:rgb(0,0,102);font-family:tahoma,sans-serif">
------------------------------------------<br>
</div>
</div>
<div style="color:rgb(0,0,102);font-family:tahoma,sans-serif"><br>
</div>
<div style="color:rgb(0,0,102);font-family:tahoma,sans-serif"><br>
</div>
<div style="color:rgb(0,0,102);font-family:tahoma,sans-serif">
And here's my chan_dahdi.conf</div>
<div style="color:rgb(0,0,102);font-family:tahoma,sans-serif"><br>
</div>
<div>
<div>
<div style="color:rgb(0,0,102);font-family:tahoma,sans-serif">------------------------------------------<br>
</div>
</div>
<div><font color="#000066" face="tahoma, sans-serif">signalling=mfcr2</font></div>
<div><font color="#000066" face="tahoma, sans-serif">mfcr2_variant=mx</font></div>
<div><font color="#000066" face="tahoma, sans-serif">mfcr2_get_ani_first=no</font></div>
<div><font color="#000066" face="tahoma, sans-serif">mfcr2_max_ani=10</font></div>
<div><font color="#000066" face="tahoma, sans-serif">mfcr2_max_dnis=4</font></div>
<div><font color="#000066" face="tahoma, sans-serif">mfcr2_category=national_subscriber</font></div>
<div><font color="#000066" face="tahoma, sans-serif">mfcr2_mfback_timeout=-1</font></div>
<div><font color="#000066" face="tahoma, sans-serif">mfcr2_metering_pulse_timeout=-1</font></div>
<div><font color="#000066" face="tahoma, sans-serif">mfcr2_forced_release=no</font></div>
<div><font color="#000066" face="tahoma, sans-serif">context=from-pstn</font></div>
<div><font color="#000066" face="tahoma, sans-serif">group=0</font></div>
<div><font color="#000066" face="tahoma, sans-serif"><br>
</font></div>
<div><font color="#000066" face="tahoma, sans-serif">mfcr2_logdir=span1</font></div>
<div><font color="#000066" face="tahoma, sans-serif">mfcr2_call_files=yes</font></div>
<div><span style="color:rgb(0,0,102);font-family:tahoma,sans-serif">mfcr2_logging=all</span><br>
</div>
<div><font color="#000066" face="tahoma, sans-serif">channel
=> 1-10</font></div>
<div style="color:rgb(0,0,102);font-family:tahoma,sans-serif">
<div style="color:rgb(34,34,34);font-family:arial">
<div style="color:rgb(0,0,102);font-family:tahoma,sans-serif">
------------------------------------------<br>
</div>
<div><br>
</div>
<div><br>
</div>
<div>Unless I just got blind, everything is
by the book (and this setup was working fine).
These are the specifics of the system:</div>
<div><br>
</div>
<div>OpenR2 1.3.2</div>
<div>Asterisk 1.8.21.0</div>
<div>Digium Wildcard TE121</div>
<div>Carrier: Telmex (México)</div>
<div>CentOS 6.4 (just recently did yum -y
upgrade so everything is the most recent version
as of today)</div>
<div><br>
</div>
<div><br>
</div>
<div>Apart from checking the config files
again and again, this is what I also tried:</div>
<div><br>
</div>
<div>- Plugging/unplugging the cable</div>
<div>- Rebooting</div>
<div>- Switching the card from PCIe slot </div>
<div><br>
</div>
<div><br>
</div>
<div>As you can imagine, Telmex says "its
fine from my side". Since everything started to
malfunction with no users involved, my guts tell
me its them, not us. How can I prove it with a
Digium card? I know the commands from Sangoma for
wanpipe debugging, but this cards are not my
strongest point when it comes to debugging. </div>
<div><br>
</div>
<div>Any ideas? Any commands I can execute
to mail Telmex and prove whose fault is this?</div>
<div><br>
</div>
<div>Regards,</div>
<div><br>
</div>
</div>
</div>
</div>
</div>
</div>
--<br>
_____________________________________________________________________<br>
-- Bandwidth and Colocation Provided by <a href="http://www.api-digital.com" target="_blank">http://www.api-digital.com</a>
--<br>
<br>
asterisk-r2 mailing list<br>
To UNSUBSCRIBE or update options visit:<br>
<a href="http://lists.digium.com/mailman/listinfo/asterisk-r2" target="_blank">http://lists.digium.com/mailman/listinfo/asterisk-r2</a></blockquote>
</div>
<br>
<br>
<fieldset></fieldset>
<br>
<pre>--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by <a href="http://www.api-digital.com" target="_blank">http://www.api-digital.com</a> --
asterisk-r2 mailing list
To UNSUBSCRIBE or update options visit:
<a href="http://lists.digium.com/mailman/listinfo/asterisk-r2" target="_blank">http://lists.digium.com/mailman/listinfo/asterisk-r2</a></pre>
</blockquote>
<br>
</div></div></div>
<br>--<br>
_____________________________________________________________________<br>
-- Bandwidth and Colocation Provided by <a href="http://www.api-digital.com" target="_blank">http://www.api-digital.com</a> --<br>
<br>
asterisk-r2 mailing list<br>
To UNSUBSCRIBE or update options visit:<br>
<a href="http://lists.digium.com/mailman/listinfo/asterisk-r2" target="_blank">http://lists.digium.com/mailman/listinfo/asterisk-r2</a><br></blockquote></div><br></div></div></div></div>