Hi, i need to connect asterisk with a Harries 20-20 Semi Public PBX with mcf/r2 protocol.<br>Mi hardware is Sangoma A101. Elastix 1.6 Realease. 1.2 libopenr2.<br>The configuration of dahdi is<br><p><font face="Courier, Monospaced">/etc/dadhi/system.conf <br>
</font></p><font face="Courier, Monospaced">span=1,1,0,cas,hdb3 <br>
cas=1-15:1101 <br> cas=17-31:1101 <br>#i test with and without this parmeter with same result.<br>dchan=16 <br><br></font><font face="Courier, Monospaced">/etc/asterisk/chan_dahdi.conf <br><br></font><font face="Courier, Monospaced">[channels] <br>
language=es <br>
signalling=mfcr2 <br> group=0 <br> mfcr2_variant=ar <br>
mfcr2_max_ani=10 <br> mfcr2_max_dnis=4 <br> mfcr2_logging=all <br>
channel=1-15 <br> channel=17-31 <br><br><br>My problem is, in all channels after init i got the message<br><br>Far end blocked on chan XXXX<br><br>The provider of the </font><font face="Courier, Monospaced">harries 20-20 tell me the variant use is AR.<br>
I use E1 crosscable to connect this pbx.<br>No alarms, the status is Green ( ok).<br><br></font><font face="Courier, Monospaced">The configuration of the harries 20-20 is <br><br><br><br>li 3-3<br><br>SLOT 03-03/32 PORTS: 2MB <br>
TONE ADJUST <br>CIRC NAME PLAN TR/RE COMMENT<br>---- ---- ---- ---- ------ -------<br><br> 1/R2DGTL TG 35 CEL D/TT 0/0 <br>
2/R2DGTL TG 35 CEL D/TT 0/0 <br> 3/R2DGTL TG 35 CEL D/TT 0/0 <br> 4/R2DGTL TG 35 CEL D/TT 0/0 <br>
5/R2DGTL TG 35 CEL D/TT 0/0 <br> 6/R2DGTL TG 35 CEL D/TT 0/0 <br> 7/R2DGTL TG 35 CEL D/TT 0/0 <br>
8/R2DGTL TG 35 CEL D/TT 0/0 <br> 9/R2DGTL ---------- D/TT 0/0 <br>10/R2DGTL ---------- D/TT 0/0 <br>
11/R2DGTL ---------- D/TT 0/0 <br>12/R2DGTL ---------- D/TT 0/0 <br>13/R2DGTL ---------- D/TT 0/0 <br>
14/R2DGTL ---------- D/TT 0/0 <br>15/R2DGTL ---------- D/TT 0/0 <br>16/IMD CTRL ---------- ----- 0/0 <br>
17/R2DGTL ---------- D/TT 0/0 <br>18/R2DGTL ---------- D/TT 0/0 <br>19/R2DGTL ---------- D/TT 0/0 <br>
20/R2DGTL ---------- D/TT 0/0 <br>21/R2DGTL ---------- D/TT 0/0 <br>22/R2DGTL ---------- D/TT 0/0 <br>
23/R2DGTL ---------- D/TT 0/0 <br>24/R2DGTL ---------- D/TT 0/0 <br>25/R2DGTL ---------- D/TT 0/0 <br>
26/R2DGTL ---------- D/TT 0/0 <br>27/R2DGTL ---------- D/TT 0/0 <br>28/R2DGTL ---------- D/TT 0/0 <br>
29/R2DGTL ---------- D/TT 0/0 <br>30/R2DGTL ---------- D/TT 0/0 <br>31/R2DGTL ---------- D/TT 0/0 <br>
32/2MB CTRL ---------- ----- 0/0 <br><br>Frame alignment signal error ................ 10 EXP-4<br>Receive frame slip counter limit ............ 254<br>Prompt maintenance prealarm counter limit ... 254<br>
Remote prealarm counter limit ............... 254<br>Out of service prealarm counter limit ....... 254<br>Prompt maintenance alarm on delay ........... 2.0 seconds<br>Prompt maintenance alarm off delay .......... 2.0 seconds<br>
Remote alarm on delay ....................... 0.3 seconds<br>Remote alarm off delay ...................... 0.3 seconds<br>Signaling type .............................. STANDARD<br>Channel 16 mode ............................. CAS<br>
<br>BOA ...? tru li 35<br><br>************************ W A R N I N G *******************************<br><br>Within this module, all ADDs, all DELetes, and some MODifys cannot be SAVed<br>unless the switch is REBooted. You will be alerted when a MODify which<br>
requires a REBoot to SAVe is encountered and you will have the option to<br>cancel it.<br><br>******************************************************************************<br><br>Trunk group number ............ 35<br>Trunk group type .............. R2DGTL<br>
Incoming class of service ..... 206 R2 <br>Trunk ID digits ............... NONE<br>No answer extension ........... NONE<br>Call flow ..................... BOTH <br>Incoming dialing mode ......... MFC <br>
Incoming lookahead signaling .. NO<br>Outgoing dialing mode ......... MFC <br>Meter pulse ................... Yes<br>Bit used for meter pulses ..... A-BIT <br>Search type ................... CIRCULAR FORWARD<br>Malicious call line signal .... No<br>
Forced release line signal .... Yes<br>Double seizure allowed ........ Yes<br>Circuit locations ............. 03-03-01 03-03-02 03-03-03 03-03-04 <br>Circuit locations ............. 03-03-05 03-03-06 03-03-07 03-03-08 <br>
Unassigned circuit locations .. 22<br>AW display name ............... CEL<br>Teleset display name .......... CEL<br>Comment ... GT-35 e1 salida celulares<br><br>TRU ...? sys<br><br>SYSEDT ...? r2<br><br>SYSR2 ...? li<br><br>
Parameter [ALL] ...? <br><br>Group A Function Signal<br>---------------- ------<br>SND A1 <br>EOS A3 <br>SND-1 A2 <br>SND-2 A7 <br>
SND-3 A8 <br>RESTART A10 <br>SND-CAT A5 <br>CONGESTION A4 <br>SPEECH A6 <br>SND-CATC N/A <br>UNALLOC A4 <br>
SND-NAT N/A <br>RESTRICT N/A <br>SND-N A9 <br><br>Group B Status Signal<br>-------------- ------<br>IDLE B6 <br>BUSY B3 <br>
NOCHARGE B7 <br>MCT B1 <br>UNALLOC B5 <br>CONGESTION B4 <br>SND-TONE B2 <br>OUT-SERV B8 <br>NUM-CHG B2 <br>
FAULTY B8 <br>UNAVAIL B5 <br><br>Group C Function Signal<br>---------------- ------<br>SND-ANIC N/A <br>RESTARTC N/A <br>EOAC N/A <br>
CONGESTION N/A <br>SNDC N/A <br>SLDC N/A <br><br>Group II Category Signal<br>----------------- ------<br>SUB-PRIORITY II2 <br>SUB-NO-PRIORITY II1 <br>
MAINT-EQUIP II3 <br>OPERATOR II1 <br>DATA-EQUIP II6 <br>SUB-NO-IDENTIFY II1 <br><br>ANI SOURCE: Auth code field<br><br>R2 Protocol Parameters<br>------------------------------------------------------------------<br>
Send ANI after Sending Category of SUB-NO-IDENTIFY...............Y<br>Send I-12 if ANI is requested, but no ANI is available...........Y<br>Release trunk after receiving undefined Group A signals..........Y<br>Send congestion tone after receiving undefined Group B signals...N<br>
Treat R2 B1 signal as Idle .....................................Y<br>Send I-12 when restarting ANI digits.............................Y<br><br><br><br>SYSR2 ...? <br><br><br><br></font><font face="Courier, Monospaced"><br>
<br><br></font>