<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 TRANSITIONAL//EN">
<HTML>
<HEAD>
  <META HTTP-EQUIV="Content-Type" CONTENT="text/html; CHARSET=UTF-8">
  <META NAME="GENERATOR" CONTENT="GtkHTML/3.26.0">
</HEAD>
<BODY>
dahdi_tool:<BR>
 Current Alarms:     Red Alarm                           │     │<BR>
   │     │    Sync Source:        Internally clocked                  │  ↑  │<BR>
   │     │    IRQ Misses:               0                             │  ▒  │<BR>
   │     │    Bipolar Viol:             0                             │  ▒  │<BR>
   │     │    Tx/Rx Levels:         0/  0                             │  ▒  │<BR>
   │     │    Total/Conf/Act:      31/ 30/ 30                         │  ▒  │<BR>
   │     │                 1111111111222222222233         ┌──────┐    │  ▒  │<BR>
   │     │        1234567890123456789012345678901         │ Back │    │  ▒  │<BR>
   │     │    TxA 111111111111111 111111111111111         └──────┘    │  ▒  │<BR>
   │     │    TxB 000000000000000 111111111111111                     │  ▮  │<BR>
   │     │    TxC 000000000000000 000000000000000                     │  ↓  │<BR>
   │     │    TxD 111111111111111 111111111111111                     │     │<BR>
   │     │                                                ┌──────┐    │     │<BR>
   │     │    RxA 111111111111111 111111111111111         │ Loop │    │     │<BR>
   │     │    RxB 111111111111111 111111111111111         └──────┘    │     │<BR>
   │     │    RxC 000000000000000 000000000000000                     │     │<BR>
   │     │    RxD 111111111111111 111111111111111                     │<BR>
<BR>
<BR>
wanrouter status:<BR>
<BR>
Devices currently active:<BR>
        wanpipe1<BR>
<BR>
<BR>
Wanpipe Config:<BR>
<BR>
Device name | Protocol Map | Adapter  | IRQ | Slot/IO | If's | CLK | Baud rate |<BR>
wanpipe1    | N/A          | A101/1D/A102/2D/4/4D/8| 169 | 4       | 1    | N/A | 0         |<BR>
<BR>
Wanrouter Status:<BR>
<BR>
Device name | Protocol | Station | Status        |<BR>
wanpipe1    | AFT TE1  | N/A     | Disconnected  |<BR>
<BR>
Does this mean that there is something wrong with the WANROUTER drivers???<BR>
<BR>
SP<BR>
<BR>
<BR>
On Thu, 2009-09-10 at 16:03 -0500, Sebastian Peschko wrote:<BR>
<BLOCKQUOTE TYPE=CITE>
    Yes they both have red alarm! Does this mean I still have a HW problem? The physical connection is exactly the same as before and I have also tried to invert the Coax just in case but it does not leave the red alarm state.<BR>
    <BR>
    SP<BR>
    <BR>
    On Thu, 2009-09-10 at 16:43 -0400, Moises Silva wrote:<BR>
    <BLOCKQUOTE TYPE=CITE>
        What does dahdi_tool or zttool say? red alarm? if you have any physical layer alarms you must fix those first before even trying to start playing with Asterisk or openr2 stuff.<BR>
        <BR>
        On Thu, Sep 10, 2009 at 4:31 PM, Sebastian Peschko <<A HREF="mailto:speschko@gmail.com">speschko@gmail.com</A>> wrote:<BR>
        <BLOCKQUOTE>
            I had Asterisk 1.25.0 and openr2-2.0.x working with a fractional E1 (ch1-15) working up to now but needed the new IAX security feature because I was being hacked.<BR>
            <BR>
            I have now installed Asterisk 1.4.26.2 with the openr2-asterisk-1.4.26.2.patch and openr2-1.2.0.I am now getting a RED alarm with all the RX channels blocked from Telmex. I have called them and they say that they see a remote alarm but on their side they are idle. On my side I have:<BR>
            <BR>
            Ch  Var    ANI   DNIS ANI First Immed       Tx CAS   Rx CAS<BR>
               1 MX      16      4        No        No               IDLE     BLOCK<BR>
               2 MX      16      4        No        No               IDLE     BLOCK<BR>
               3 MX      16      4        No        No               IDLE     BLOCK<BR>
               4 MX      16      4        No        No               IDLE     BLOCK<BR>
               5 MX      16      4        No        No               IDLE     BLOCK<BR>
               6 MX      16      4        No        No               IDLE     BLOCK<BR>
               7 MX      16      4        No        No               IDLE     BLOCK<BR>
               8 MX      16      4        No        No               IDLE     BLOCK<BR>
               9 MX      16      4        No        No               IDLE     BLOCK<BR>
              10 MX      16      4        No        No               IDLE     BLOCK<BR>
              11 MX      16      4        No        No               IDLE     BLOCK<BR>
              12 MX      16      4        No        No               IDLE     BLOCK<BR>
              13 MX      16      4        No        No               IDLE     BLOCK<BR>
              14 MX      16      4        No        No               IDLE     BLOCK<BR>
              15 MX      16      4        No        No               IDLE     BLOCK<BR>
            <BR>
            Is there anyone running this software and has this running or has suggestions to what I might be doing wrong?<BR>
            <BR>
            <BR>
            <BR>
            _______________________________________________<BR>
            --Bandwidth and Colocation Provided by <A HREF="http://www.api-digital.com--">http://www.api-digital.com--</A><BR>
            <BR>
            asterisk-r2 mailing list<BR>
            To UNSUBSCRIBE or update options visit:<BR>
              <A HREF="http://lists.digium.com/mailman/listinfo/asterisk-r2">http://lists.digium.com/mailman/listinfo/asterisk-r2</A> <BR>
        </BLOCKQUOTE>
        <BR>
        <BR>
        <BR>
        -- <BR>
        Moises Silva<BR>
        Software Developer<BR>
        Sangoma Technologies Inc. | 50 McIntosh Drive, Suite 120, Markham ON L3R 9T3 Canada<BR>
        t. 1 905 474 1990 x 128 | e. <A HREF="mailto:moy@sangoma.com">moy@sangoma.com</A>
    </BLOCKQUOTE>
</BLOCKQUOTE>
</BODY>
</HTML>