[asterisk-r2] Problem Sending call PBX(nortel) --- asterisk -- TELCO

Thu Feb 23 20:36:00 CST 2012

Carlos
Good sounds, great! congratulations!

Well MFCR2 have these kind of issues and it look limited, and becomes from compelled digit length number, well at these stage I couldn't said  exactly how to resolve, but I have an idea.
Basically I think to divide  E1 trunk channels on both side in order to send different digit length number, in case of Asterisk on dahdi-channels.conf  you can set channels it could be see bottom of configuration so it could be on the same span 2 context applied to different channel and digit length.
In the other side should have to do call routing table to redirect digit length to the right channels otherwise, could happens incorrect disconnection causes.
If these it work it have a limitation of quantity call routes, but if work you can adjust according to traffic measurement and analysis.

Configuration for less quantity digits numbers

; Span 2: TE2/0/2 "T2XXP (PCI) Card 0 Span 2"
mfcr2_skip_category=yes
group=2
;switchtype = euroisdn
signalling =mfcr2
mfcr2_variant=itu
mfcr2_get_ani_first=yes
mfcr2_max_ani=4
mfcr2_max_dnis=4
callerid=asreceived
mfcr2_category=national_priority_subscribe
mfcr2_logdir=span1
mfcr2_call_files=yes
mfcr2_logging=all
mfcr2_mfback_timeout=-1
mfcr2_metering_pulse_timeout=-1
mfcr2_allow_collect_calls=no
mfcr2_double_answer=no
mfcr2_forced_release=no
mfcr2_charge_calls=yes
mfcr2_skip_category=no
callerid=asreceived
context=salida
channel => 32-46

Configuration for 7 digits number length

; Span 2: TE2/0/2 "T2XXP (PCI) Card 0 Span 2"
mfcr2_skip_category=yes
group=2
;switchtype = euroisdn
signalling =mfcr2
mfcr2_variant=itu
mfcr2_get_ani_first=yes
mfcr2_max_ani=4
mfcr2_max_dnis=7
callerid=asreceived
mfcr2_category=national_priority_subscribe
mfcr2_logdir=span1
mfcr2_call_files=yes
mfcr2_logging=all
mfcr2_mfback_timeout=-1
mfcr2_metering_pulse_timeout=-1
mfcr2_allow_collect_calls=no
mfcr2_double_answer=no
mfcr2_forced_release=no
mfcr2_charge_calls=yes
mfcr2_skip_category=no
callerid=asreceived
context=salida
channel => 48-62

Please check dialplan if you have assign context (DAHDI/g/${EXTEN})

Best regards
Mc GRATH Ricardo
E-Mail mcgrathr at mail2web.com<mailto:mcgrathr at mail2web.com>

________________________________
From: asterisk-r2-bounces at lists.digium.com [asterisk-r2-bounces at lists.digium.com] On Behalf Of Carlos Rodriguez Alcala [carlos.rav at gmail.com]
Sent: 23 February 2012 22:20
To: asterisk-r2 at lists.digium.com
Subject: Re: [asterisk-r2] Problem Sending call PBX(nortel) --- asterisk -- TELCO

Hi Ricardo,

It works!! thanks.

I still have a problem... I have to call to numbers with 6 or 7 digits(sometimes 3 numbers), but if I put 6 on mfcr2_max_dnis it only allow me to dial 6 digits and then send the call.
If I put 7 digits(on mfcr2_max_dnis=7) I only can call to numbers 7 digits, if I call  6 digits (with mfcr2_max_dnis=7) sound me like busy after few seconds.
This is the configuration of de E1 (side pbx) and then the log of a sucefull call(7 digits, on chanel 46) and a fail log (6 digits, on channel 45).

In the debug it like always expect "expected length: 7" no less than that!!
How can I do?

; Span 2: TE2/0/2 "T2XXP (PCI) Card 0 Span 2"
mfcr2_skip_category=yes
group=2
;switchtype = euroisdn
signalling =mfcr2
mfcr2_variant=itu
mfcr2_get_ani_first=yes
mfcr2_max_ani=4
mfcr2_max_dnis=7
callerid=asreceived
mfcr2_category=national_priority_subscribe
mfcr2_logdir=span1
mfcr2_call_files=yes
mfcr2_logging=all
mfcr2_mfback_timeout=-1
mfcr2_metering_pulse_timeout=-1
mfcr2_allow_collect_calls=no
mfcr2_double_answer=no
mfcr2_forced_release=no
mfcr2_charge_calls=yes
mfcr2_skip_category=no
callerid=asreceived
context=salida
channel => 32-46,48-62
#################################################
channel 46

http://pastebin.com/iASqWrSP
#############

channel 45
http://pastebin.com/gLV38UbT

2012/2/22 Mc GRATH Ricardo <mcgrathr at mail2web.com<mailto:mcgrathr at mail2web.com>>
Carlos

I probably sure problem it becomes from the rule setting on dialplan that you have assign, just in case of your settings of " .," is not a good setting it mean Asterisk can dial one or more digits, by the way  it can causes great potential to cause problems, these last is not from me.
So I have an idea to test dialplan  if working properly.
Could assign context [salida] to one Asterisk SIP device and use for test of dialplan rules?
By the other way I change salida rules to the following, it should work.
[salida]
exten => _x.,1,Progress()
exten => _X.,n,Dial(DAHDI/g1/${EXTEN})

Try it and let me know the test result

Mc GRATH Ricardo
E-Mail mcgrathr at mail2web.com<mailto:mcgrathr at mail2web.com>

________________________________
From: asterisk-r2-bounces at lists.digium.com<mailto:asterisk-r2-bounces at lists.digium.com> [asterisk-r2-bounces at lists.digium.com<mailto:asterisk-r2-bounces at lists.digium.com>] On Behalf Of Carlos Rodriguez Alcala [carlos.rav at gmail.com<mailto:carlos.rav at gmail.com>]
Sent: 22 February 2012 11:50

To: asterisk-r2 at lists.digium.com<mailto:asterisk-r2 at lists.digium.com>
Subject: Re: [asterisk-r2] Problem Sending call PBX(nortel) --- asterisk -- TELCO

Ok I will set asterisk -vvvr !! :D
For now there´s no way, I´ll ask for PBX tech, But If I connect directly TELCO-PBX works well.

2012/2/22 Mc GRATH Ricardo <mcgrathr at mail2web.com<mailto:mcgrathr at mail2web.com>>
Thanks

Well how about to set core set verbose 3 to see what's  going on when call is performing?
No way to get a trace from Nortel?

Mc GRATH Ricardo
E-Mail mcgrathr at mail2web.com<mailto:mcgrathr at mail2web.com>

________________________________
From: asterisk-r2-bounces at lists.digium.com<mailto:asterisk-r2-bounces at lists.digium.com> [asterisk-r2-bounces at lists.digium.com<mailto:asterisk-r2-bounces at lists.digium.com>] On Behalf Of Carlos Rodriguez Alcala [carlos.rav at gmail.com<mailto:carlos.rav at gmail.com>]
Sent: 22 February 2012 11:08

To: asterisk-r2 at lists.digium.com<mailto:asterisk-r2 at lists.digium.com>
Subject: Re: [asterisk-r2] Problem Sending call PBX(nortel) --- asterisk -- TELCO

Hi Ricardo,

I have a digium card with 2 E1, I want to record the calls, so I have  PBX ----E1 ----Elastix-----E1 ---- TELCO.
As you can see in my chan_dahdi.conf:
context= salida

and

extensions.conf

[salida]
exten => .,1,Answer
exten => .,2,set(calltime=${STRFTIME(${EPOCH},,%C%y-%m-%d--%H\:%M\:%S)})
exten => .,3,MixMonitor(E_${calltime}_from_${CALLERID(num)}to__${EXTEN}.wav)
exten => .,n,Dial(DAHDI/g1/${EXTEN})
exten => h,1,Hangup

2012/2/22 Mc GRATH Ricardo <mcgrathr at mail2web.com<mailto:mcgrathr at mail2web.com>>
Hi

What kind of connection you have between PBX (nortel) to Asterisk?
If a E1 could you get a trace from Nortel to Asterisk?
It probably you have to review your dialplan for call rerouting from external device via Asterisk, it will help to get trace from external device from Asterisk to let you know the call disconnection cause.
Best regards

Mc GRATH Ricardo
E-Mail mcgrathr at mail2web.com<mailto:mcgrathr at mail2web.com>

________________________________
From: asterisk-r2-bounces at lists.digium.com<mailto:asterisk-r2-bounces at lists.digium.com> [asterisk-r2-bounces at lists.digium.com<mailto:asterisk-r2-bounces at lists.digium.com>] On Behalf Of omar ivan perez vargas [o_i_p_v at hotmail.com<mailto:o_i_p_v at hotmail.com>]
Sent: 22 February 2012 09:40
To: asterisk-r2 at lists.digium.com<mailto:asterisk-r2 at lists.digium.com>
Subject: Re: [asterisk-r2] Problem Sending call PBX(nortel) --- asterisk -- TELCO

--
Atentamente,

Carlos Rodríguez Alcalá Villagra

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.digium.com/pipermail/asterisk-r2/attachments/20120223/ff7252d2/attachment.htm>