[asterisk-r2] MFCR2 With Unicall - can unicall affect zaptel commands?
Giovanny Magallanes
gmagallanes at gmail.com
Tue Apr 7 13:35:20 CDT 2009
Thanks, Juan Carlos.
Yes, I still can t type the commands in the asterisk console . I dont have
dial tone for FXS ports .
Regards.
Giovanni.
2009/4/7, Juan Carlos Huerta <juancarloshuerta at gmail.com>:
>
> And what is the result? still with zap commands problem?
>
> Juan Carlos
> ~ Lo que no te mata te fortalece ~
>
>
>
> On Tue, Apr 7, 2009 at 12:49 PM, Giovanny Magallanes
> <gmagallanes at gmail.com> wrote:
> > I did it:
> >
> > elastix*CLI> load chan_zap.so
> > The 'load' command is deprecated and will be removed in a future release.
> > Please use 'module load' instead.
> > == Parsing '/etc/asterisk/zapata.conf': Found
> > == Parsing '/etc/asterisk/zapata_additional.conf': Found
> > == Parsing '/etc/asterisk/zapata-channels.conf': Found
> > -- Registered channel 63, FXO Kewlstart signalling
> > -- Registered channel 64, FXO Kewlstart signalling
> > -- Registered channel 65, FXO Kewlstart signalling
> > -- Registered channel 66, FXO Kewlstart signalling
> > -- Registered channel 67, FXO Kewlstart signalling
> > -- Registered channel 68, FXO Kewlstart signalling
> > -- Registered channel 68, FXO Kewlstart signalling
> > -- Registered channel 69, FXO Kewlstart signalling
> > -- Registered channel 70, FXO Kewlstart signalling
> > -- Registered channel 71, FXO Kewlstart signalling
> > -- Registered channel 72, FXO Kewlstart signalling
> > -- Registered channel 73, FXO Kewlstart signalling
> > -- Registered channel 74, FXO Kewlstart signalling
> > -- Registered channel 75, FXO Kewlstart signalling
> > -- Registered channel 76, FXO Kewlstart signalling
> > -- Registered channel 77, FXO Kewlstart signalling
> > -- Registered channel 78, FXO Kewlstart signalling
> > elastix*CLI>
> >
> > Thank you Juan
> >
> > Giovanni
> >
> >
> > 2009/4/7, Juan Carlos Huerta <juancarloshuerta at gmail.com>:
> >>
> >> Try to load the chan_zap.so module manually to see if you get some
> error.
> >>
> >> Juan Carlos
> >> ~ Lo que no te mata te fortalece ~
> >>
> >>
> >>
> >> On Tue, Apr 7, 2009 at 12:44 PM, Giovanny Magallanes
> >> <gmagallanes at gmail.com> wrote:
> >> > I'm using Elastix 1.1-8 with:
> >> >
> >> > asterisk-1.4.19
> >> > spandsp-0.0.4
> >> > unicall-0.0.5pre1
> >> > zaptel-1.4.9.2
> >> > unicall-0.0.5pre1
> >> > libmfcr2-0.0.3
> >> > libsupertone-0.0.2
> >> > libunicall-0.0.3
> >> >
> >> > Regards,
> >> >
> >> > Giovanni
> >> >
> >> > 2009/4/7, Giovanny Magallanes <gmagallanes at gmail.com>:
> >> >>
> >> >> Ok, Thanks. The chan_zap commands are unavailable, but unicall
> commands
> >> >> and my E1 MFC/R2 are OK.
> >> >>
> >> >> Giovanni
> >> >>
> >> >>
> >> >> 2009/4/7, Moises Silva <moises.silva at gmail.com>:
> >> >>>
> >> >>> I don't understand your problem. And no, unicall has nothing to do
> >> >>> with chan_zap.so commands.
> >> >>>
> >> >>> Please, in the future, don't hijack threads, open a new thread for
> >> >>> your discussion. This time I changed the subject already.
> >> >>>
> >> >>> Moy
> >> >>>
> >> >>> On Tue, Apr 7, 2009 at 1:08 AM, Giovanny Magallanes
> >> >>> <gmagallanes at gmail.com> wrote:
> >> >>> > Hi, Guys.
> >> >>> >
> >> >>> > I did not type any zaptel commands in asterisk console. I have
> >> >>> > installed
> >> >>> > Elastix 1.1-8 with unicall and it is working fine with a Digium
> >> >>> > TE212-P.
> >> >>> >
> >> >>> > [root at elastix asterisk]# find -P / -name chan_zap.so
> >> >>> > /usr/lib/asterisk/modules/chan_zap.so
> >> >>> >
> /usr/src/astunicall-1.4.19-0.1/asterisk-1.4.19/channels/chan_zap.so
> >> >>> > [root at elastix asterisk]#
> >> >>> > elastix*CLI> load chan_zap.so
> >> >>> > == Parsing '/etc/asterisk/zapata.conf': Found
> >> >>> > == Parsing '/etc/asterisk/zapata_additional.conf': Found
> >> >>> > == Parsing '/etc/asterisk/zapata-channels.conf': Found
> >> >>> > -- Registered channel 63, FXO Kewlstart signalling
> >> >>> > -- Registered channel 64, FXO Kewlstart signalling
> >> >>> > -- Registered channel 65, FXO Kewlstart signalling
> >> >>> > -- Registered channel 66, FXO Kewlstart signalling
> >> >>> >
> >> >>> >
> >> >>> > Can unicall affect zaptel commands in asterisk??
> >> >>> >
> >> >>> > Thanks
> >> >>> >
> >> >>> > Giovanni Magallanes
> >> >>> >
> >> >>> >
> >> >>> >
> >> >>> > 2009/4/6, Fernando Berretta <fernando.berretta at gmail.com>:
> >> >>> >>
> >> >>> >> Hi,
> >> >>> >>
> >> >>> >> I've installed Asterisk 1.4 and Openr2 1.1 all is working well.
> >> >>> >> I've
> >> >>> >> connected a crossover cable to TE122 board and board lite has
> went
> >> >>> >> green. But when I've tried to make a call, I've got the
> following
> >> >>> >> trace:
> >> >>> >>
> >> >>> >> [15:35:00:218] [Thread: 3078437776] [Chan 1] - Call started at
> Mon
> >> >>> >> Apr
> >> >>> >> 6 15:35:00 2009 on chan 1
> >> >>> >> [15:35:00:218] [Thread: 3078437776] [Chan 1] - CAS Tx >> [SEIZE]
> >> >>> >> 0x00
> >> >>> >> [15:35:00:218] [Thread: 3078437776] [Chan 1] - CAS Raw Tx >> 0x01
> >> >>> >> [15:35:00:242] [Thread: 3078437776] [Chan 1] - Bits changed from
> >> >>> >> 0x08
> >> >>> >> to
> >> >>> >> 0x00
> >> >>> >> [15:35:00:242] [Thread: 3078437776] [Chan 1] - CAS Rx << [FORCED
> >> >>> >> RELEASE] 0x00
> >> >>> >> [15:35:00:242] [Thread: 3078437776] [Chan 1] - Disconnection
> before
> >> >>> >> seize ack detected![15:35:00:242] [Thread: 3078437776] [Chan 1] -
> >> >>> >> Far
> >> >>> >> end disconnected. Reason: Forced Release
> >> >>> >> [15:35:00:245] [Thread: 3078437776] [Chan 1] - Attempting to
> cancel
> >> >>> >> timer timer 0
> >> >>> >> [15:35:00:245] [Thread: 3078437776] [Chan 1] - Cannot cancel
> timer
> >> >>> >> 0
> >> >>> >> [15:35:00:245] [Thread: 3078437776] [Chan 1] - CAS Tx >> [CLEAR
> >> >>> >> FORWARD]
> >> >>> >> 0x08
> >> >>> >> [15:35:00:245] [Thread: 3078437776] [Chan 1] - CAS Raw Tx >> 0x09
> >> >>> >> [15:35:00:306] [Thread: 3081632656] [Chan 1] - Bits changed from
> >> >>> >> 0x00
> >> >>> >> to
> >> >>> >> 0x08
> >> >>> >> [15:35:00:306] [Thread: 3081632656] [Chan 1] - CAS Rx << [IDLE]
> >> >>> >> 0x08
> >> >>> >> [15:35:00:306] [Thread: 3081632656] [Chan 1] - Call ended
> >> >>> >> [15:35:00:306] [Thread: 3081632656] [Chan 1] - Attempting to
> cancel
> >> >>> >> timer timer 0
> >> >>> >> [15:35:00:306] [Thread: 3081632656] [Chan 1] - Cannot cancel
> timer
> >> >>> >> 0
> >> >>> >>
> >> >>> >> Is there some way to complete a call through crossover cable with
> >> >>> >> R2 ?
> >> >>> >> How should I configure dahdi ?
> >> >>> >>
> >> >>> >> Best Regards,
> >> >>> >> Fernando
> >> >>> >>
> >> >>> >> _______________________________________________
> >> >>> >> --Bandwidth and Colocation Provided by
> http://www.api-digital.com--
> >> >>> >>
> >> >>> >> asterisk-r2 mailing list
> >> >>> >> To UNSUBSCRIBE or update options visit:
> >> >>> >> http://lists.digium.com/mailman/listinfo/asterisk-r2
> >> >>> >
> >> >>> >
> >> >>> > _______________________________________________
> >> >>> > --Bandwidth and Colocation Provided by
> http://www.api-digital.com--
> >> >>> >
> >> >>> > asterisk-r2 mailing list
> >> >>> > To UNSUBSCRIBE or update options visit:
> >> >>> > http://lists.digium.com/mailman/listinfo/asterisk-r2
> >> >>> >
> >> >>>
> >> >>>
> >> >>>
> >> >>> --
> >> >>> "I do not agree with what you have to say, but I’ll defend to the
> >> >>> death your right to say it." Voltaire
> >> >>>
> >> >>> _______________________________________________
> >> >>> --Bandwidth and Colocation Provided by http://www.api-digital.com--
> >> >>>
> >> >>> asterisk-r2 mailing list
> >> >>> To UNSUBSCRIBE or update options visit:
> >> >>> http://lists.digium.com/mailman/listinfo/asterisk-r2
> >> >
> >> >
> >> > _______________________________________________
> >> > --Bandwidth and Colocation Provided by http://www.api-digital.com--
> >> >
> >> > asterisk-r2 mailing list
> >> > To UNSUBSCRIBE or update options visit:
> >> > http://lists.digium.com/mailman/listinfo/asterisk-r2
> >> >
> >>
> >> _______________________________________________
> >> --Bandwidth and Colocation Provided by http://www.api-digital.com--
> >>
> >> asterisk-r2 mailing list
> >> To UNSUBSCRIBE or update options visit:
> >> http://lists.digium.com/mailman/listinfo/asterisk-r2
> >
> >
> > _______________________________________________
> > --Bandwidth and Colocation Provided by http://www.api-digital.com--
> >
> > asterisk-r2 mailing list
> > To UNSUBSCRIBE or update options visit:
> > http://lists.digium.com/mailman/listinfo/asterisk-r2
> >
>
> _______________________________________________
> --Bandwidth and Colocation Provided by http://www.api-digital.com--
>
> asterisk-r2 mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-r2
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-r2/attachments/20090407/e64ffa24/attachment-0001.htm
More information about the asterisk-r2
mailing list