[aadk-commits] qwell: uClinux/trunk r50 -
/uClinux/trunk/uClinux-dist/defaults/etc/asterisk/
aadk-commits at lists.digium.com
aadk-commits at lists.digium.com
Fri Nov 10 17:04:59 MST 2006
Author: qwell
Date: Fri Nov 10 18:04:58 2006
New Revision: 50
URL: http://svn.digium.com/view/aadk?view=rev&rev=50
Log:
Remove comments - prepare to change to a .in file, ala zaptel.conf.in
Modified:
uClinux/trunk/uClinux-dist/defaults/etc/asterisk/zapata.conf
Modified: uClinux/trunk/uClinux-dist/defaults/etc/asterisk/zapata.conf
URL: http://svn.digium.com/view/aadk/uClinux/trunk/uClinux-dist/defaults/etc/asterisk/zapata.conf?view=diff&rev=50&r1=49&r2=50
==============================================================================
--- uClinux/trunk/uClinux-dist/defaults/etc/asterisk/zapata.conf (original)
+++ uClinux/trunk/uClinux-dist/defaults/etc/asterisk/zapata.conf Fri Nov 10 18:04:58 2006
@@ -1,588 +1,23 @@
-;
-; Zapata telephony interface
-;
-; Configuration file
-;
-; You need to restart Asterisk to re-configure the Zap channel
-; CLI> reload chan_zap.so
-; will reload the configuration file,
-; but not all configuration options are
-; re-configured during a reload.
-
-
-
[trunkgroups]
-;
-; Trunk groups are used for NFAS or GR-303 connections.
-;
-; Group: Defines a trunk group.
-; group => <trunkgroup>,<dchannel>[,<backup1>...]
-;
-; trunkgroup is the numerical trunk group to create
-; dchannel is the zap channel which will have the
-; d-channel for the trunk.
-; backup1 is an optional list of backup d-channels.
-;
-;trunkgroup => 1,24,48
-;trunkgroup => 1,24
-;
-; Spanmap: Associates a span with a trunk group
-; spanmap => <zapspan>,<trunkgroup>[,<logicalspan>]
-;
-; zapspan is the zap span number to associate
-; trunkgroup is the trunkgroup (specified above) for the mapping
-; logicalspan is the logical span number within the trunk group to use.
-; if unspecified, no logical span number is used.
-;
-;spanmap => 1,1,1
-;spanmap => 2,1,2
-;spanmap => 3,1,3
-;spanmap => 4,1,4
[channels]
-;
-; Default language
-;
-;language=en
-;
-; Default context
-;
context=default
-;
-; Switchtype: Only used for PRI.
-;
-; national: National ISDN 2 (default)
-; dms100: Nortel DMS100
-; 4ess: AT&T 4ESS
-; 5ess: Lucent 5ESS
-; euroisdn: EuroISDN
-; ni1: Old National ISDN 1
-; qsig: Q.SIG
-;
switchtype=national
-;
-; Some switches (AT&T especially) require network specific facility IE
-; supported values are currently 'none', 'sdn', 'megacom', 'accunet'
-;
-;nsf=none
-;
-; PRI Dialplan: Only RARELY used for PRI.
-;
-; unknown: Unknown
-; private: Private ISDN
-; local: Local ISDN
-; national: National ISDN
-; international: International ISDN
-;
-;pridialplan=national
-;
-; PRI Local Dialplan: Only RARELY used for PRI (sets the calling number's numbering plan)
-;
-; unknown: Unknown
-; private: Private ISDN
-; local: Local ISDN
-; national: National ISDN
-; international: International ISDN
-;
-;prilocaldialplan=national
-;
-; PRI callerid prefixes based on the given TON/NPI (dialplan)
-; This is especially needed for euroisdn E1-PRIs
-;
-; sample 1 for Germany
-;internationalprefix = 00
-;nationalprefix = 0
-;localprefix = 0711
-;privateprefix = 07115678
-;unknownprefix =
-;
-; sample 2 for Germany
-;internationalprefix = +
-;nationalprefix = +49
-;localprefix = +49711
-;privateprefix = +497115678
-;unknownprefix =
-;
-; PRI resetinterval: sets the time in seconds between restart of unused
-; channels, defaults to 3600; minimum 60 seconds. Some PBXs don't like
-; channel restarts. so set the interval to a very long interval e.g. 100000000
-; or 'never' to disable *entirely*.
-;
-;resetinterval = 3600
-;
-; Overlap dialing mode (sending overlap digits)
-;
-;overlapdial=yes
-;
-; PRI Out of band indications.
-; Enable this to report Busy and Congestion on a PRI using out-of-band
-; notification. Inband indication, as used by Asterisk doesn't seem to work
-; with all telcos.
-;
-; outofband: Signal Busy/Congestion out of band with RELEASE/DISCONNECT
-; inband: Signal Busy/Congestion using in-band tones
-;
-; priindication = outofband
-;
-; If you need to override the existing channels selection routine and force all
-; PRI channels to be marked as exclusively selected, set this to yes.
-; priexclusive = yes
-;
-; ISDN Timers
-; All of the ISDN timers and counters that are used are configurable. Specify
-; the timer name, and its value (in ms for timers).
-;
-; pritimer => t200,1000
-; pritimer => t313,4000
-;
-; To enable transmission of facility-based ISDN supplementary services (such
-; as caller name from CPE over facility), enable this option.
-; facilityenable = yes
-;
-;
-; Signalling method (default is fxs). Valid values:
-; em: E & M
-; em_w: E & M Wink
-; featd: Feature Group D (The fake, Adtran style, DTMF)
-; featdmf: Feature Group D (The real thing, MF (domestic, US))
-; featdmf_ta: Feature Group D (The real thing, MF (domestic, US)) through
-; a Tandem Access point
-; featb: Feature Group B (MF (domestic, US))
-; fxs_ls: FXS (Loop Start)
-; fxs_gs: FXS (Ground Start)
-; fxs_ks: FXS (Kewl Start)
-; fxo_ls: FXO (Loop Start)
-; fxo_gs: FXO (Ground Start)
-; fxo_ks: FXO (Kewl Start)
-; pri_cpe: PRI signalling, CPE side
-; pri_net: PRI signalling, Network side
-; gr303fxoks_net: GR-303 Signalling, FXO Loopstart, Network side
-; gr303fxsks_cpe: GR-303 Signalling, FXS Loopstart, CPE side
-; sf: SF (Inband Tone) Signalling
-; sf_w: SF Wink
-; sf_featd: SF Feature Group D (The fake, Adtran style, DTMF)
-; sf_featdmf: SF Feature Group D (The real thing, MF (domestic, US))
-; sf_featb: SF Feature Group B (MF (domestic, US))
-; e911: E911 (MF) style signalling
-;
-; The following are used for Radio interfaces:
-; fxs_rx: Receive audio/COR on an FXS kewlstart interface (FXO at the
-; channel bank)
-; fxs_tx: Transmit audio/PTT on an FXS loopstart interface (FXO at the
-; channel bank)
-; fxo_rx: Receive audio/COR on an FXO loopstart interface (FXS at the
-; channel bank)
-; fxo_tx: Transmit audio/PTT on an FXO groundstart interface (FXS at
-; the channel bank)
-; em_rx: Receive audio/COR on an E&M interface (1-way)
-; em_tx: Transmit audio/PTT on an E&M interface (1-way)
-; em_txrx: Receive audio/COR AND Transmit audio/PTT on an E&M interface
-; (2-way)
-; em_rxtx: Same as em_txrx (for our dyslexic friends)
-; sf_rx: Receive audio/COR on an SF interface (1-way)
-; sf_tx: Transmit audio/PTT on an SF interface (1-way)
-; sf_txrx: Receive audio/COR AND Transmit audio/PTT on an SF interface
-; (2-way)
-; sf_rxtx: Same as sf_txrx (for our dyslexic friends)
-;
-signalling=fxo_ls
-;
-; For Feature Group D Tandem access, to set the default CIC and OZZ use these
-; parameters:
-;defaultozz=0000
-;defaultcic=303
-;
-; A variety of timing parameters can be specified as well
-; Including:
-; prewink: Pre-wink time (default 50ms)
-; preflash: Pre-flash time (default 50ms)
-; wink: Wink time (default 150ms)
-; flash: Flash time (default 750ms)
-; start: Start time (default 1500ms)
-; rxwink: Receiver wink time (default 300ms)
-; rxflash: Receiver flashtime (default 1250ms)
-; debounce: Debounce timing (default 600ms)
-;
-rxwink=300 ; Atlas seems to use long (250ms) winks
-;
-; How long generated tones (DTMF and MF) will be played on the channel
-; (in miliseconds)
-;toneduration=100
-;
-; Whether or not to do distinctive ring detection on FXO lines
-;
-;usedistinctiveringdetection=yes
-
-;
-; Whether or not to use caller ID
-;
usecallerid=yes
-;
-; Type of caller ID signalling in use
-; bell = bell202 as used in US
-; v23 = v23 as used in the UK
-; dtmf = DTMF as used in Denmark, Sweden and Netherlands
-;
-;cidsignalling=bell
-;
-; What signals the start of caller ID
-; ring = a ring signals the start
-; polarity = polarity reversal signals the start
-;
-;cidstart=ring
-;
-; Whether or not to hide outgoing caller ID (Override with *67 or *82)
-;
hidecallerid=no
-;
-; Whether or not to enable call waiting on FXO lines
-;
callwaiting=yes
-;
-; Whether or not restrict outgoing caller ID (will be sent as ANI only, not
-; available for the user)
-; Mostly use with FXS ports
-;
-;restrictcid=no
-;
-; Whether or not use the caller ID presentation for the outgoing call that the
-; calling switch is sending.
-;
usecallingpres=yes
-;
-; Some countries (UK) have ring tones with different ring tones (ring-ring),
-; which means the callerid needs to be set later on, and not just after
-; the first ring, as per the default.
-;
-;sendcalleridafter=1
-;
-;
-; Support Caller*ID on Call Waiting
-;
callwaitingcallerid=yes
-;
-; Support three-way calling
-;
threewaycalling=yes
-;
-; Support flash-hook call transfer (requires three way calling)
-; Also enables call parking (overrides the 'canpark' parameter)
-;
transfer=yes
-;
-; Allow call parking
-; ('canpark=no' is overridden by 'transfer=yes')
-;
canpark=yes
-;
-; Support call forward variable
-;
cancallforward=yes
-;
-; Whether or not to support Call Return (*69)
-;
callreturn=yes
-;
-; Stutter dialtone support: If a mailbox is specified without a voicemail
-; context, then when voicemail is received in a mailbox in the default
-; voicemail context in voicemail.conf, taking the phone off hook will cause a
-; stutter dialtone instead of a normal one.
-;
-; If a mailbox is specified *with* a voicemail context, the same will result
-; if voicemail recieved in mailbox in the specified voicemail context.
-;
-; for default voicemail context, the example below is fine:
-;
-;mailbox=1234
-;
-; for any other voicemail context, the following will produce the stutter tone:
-;
-;mailbox=1234 at context
-;
-; Enable echo cancellation
-; Use either "yes", "no", or a power of two from 32 to 256 if you wish to
-; actually set the number of taps of cancellation.
-;
echocancel=yes
-;
-; Generally, it is not necessary (and in fact undesirable) to echo cancel when
-; the circuit path is entirely TDM. You may, however, reverse this behavior
-; by enabling the echo cancel during pure TDM bridging below.
-;
echocancelwhenbridged=yes
-;
-; In some cases, the echo canceller doesn't train quickly enough and there
-; is echo at the beginning of the call. Enabling echo training will cause
-; asterisk to briefly mute the channel, send an impulse, and use the impulse
-; response to pre-train the echo canceller so it can start out with a much
-; closer idea of the actual echo. Value may be "yes", "no", or a number of
-; milliseconds to delay before training (default = 400)
-;
-;echotraining=yes
-;echotraining=800
-;
-; If you are having trouble with DTMF detection, you can relax the DTMF
-; detection parameters. Relaxing them may make the DTMF detector more likely
-; to have "talkoff" where DTMF is detected when it shouldn't be.
-;
-;relaxdtmf=yes
-;
-; You may also set the default receive and transmit gains (in dB)
-;
rxgain=0.0
txgain=0.0
-;
-; Logical groups can be assigned to allow outgoing rollover. Groups range
-; from 0 to 63, and multiple groups can be specified.
-;
group=1
-;
-; Ring groups (a.k.a. call groups) and pickup groups. If a phone is ringing
-; and it is a member of a group which is one of your pickup groups, then
-; you can answer it by picking up and dialing *8#. For simple offices, just
-; make these both the same
-;
callgroup=1
pickupgroup=1
-
-;
-; Specify whether the channel should be answered immediately or if the simple
-; switch should provide dialtone, read digits, etc.
-;
immediate=no
-;
-; Specify whether flash-hook transfers to 'busy' channels should complete or
-; return to the caller performing the transfer (default is yes).
-;
-;transfertobusy=no
-;
-; CallerID can be set to "asreceived" or a specific number if you want to
-; override it. Note that "asreceived" only applies to trunk interfaces.
-;
-;callerid=2564286000
-;
-; AMA flags affects the recording of Call Detail Records. If specified
-; it may be 'default', 'omit', 'billing', or 'documentation'.
-;
-;amaflags=default
-;
-; Channels may be associated with an account code to ease
-; billing
-;
-;accountcode=lss0101
-;
-; ADSI (Analog Display Services Interface) can be enabled on a per-channel
-; basis if you have (or may have) ADSI compatible CPE equipment
-;
-;adsi=yes
-;
-; On trunk interfaces (FXS) and E&M interfaces (E&M, Wink, Feature Group D
-; etc, it can be useful to perform busy detection either in an effort to
-; detect hangup or for detecting busies. This enables listening for
-; the beep-beep busy pattern.
-;
-;busydetect=yes
-;
-; If busydetect is enabled, it is also possible to specify how many busy tones
-; to wait for before hanging up. The default is 4, but better results can be
-; achieved if set to 6 or even 8. Mind that the higher the number, the more
-; time that will be needed to hangup a channel, but lowers the probability
-; that you will get random hangups.
-;
-;busycount=4
-;
-; If busydetect is enabled, it is also possible to specify the cadence of your
-; busy signal. In many countries, it is 500msec on, 500msec off. Without
-; busypattern specified, we'll accept any regular sound-silence pattern that
-; repeats <busycount> times as a busy signal. If you specify busypattern,
-; then we'll further check the length of the sound (tone) and silence, which
-; will further reduce the chance of a false positive.
-;
-;busypattern=500,500
-;
-; NOTE: In the Asterisk Makefile you'll find further options to tweak the busy
-; detector. If your country has a busy tone with the same length tone and
-; silence (as many countries do), consider defining the
-; -DBUSYDETECT_COMPARE_TONE_AND_SILENCE option.
-;
-; Use a polarity reversal to mark when a outgoing call is answered by the
-; remote party.
-;
-;answeronpolarityswitch=yes
-;
-; In some countries, a polarity reversal is used to signal the disconnect of a
-; phone line. If the hanguponpolarityswitch option is selected, the call will
-; be considered "hung up" on a polarity reversal.
-;
-;hanguponpolarityswitch=yes
-;
-; On trunk interfaces (FXS) it can be useful to attempt to follow the progress
-; of a call through RINGING, BUSY, and ANSWERING. If turned on, call
-; progress attempts to determine answer, busy, and ringing on phone lines.
-; This feature is HIGHLY EXPERIMENTAL and can easily detect false answers,
-; so don't count on it being very accurate.
-;
-; Few zones are supported at the time of this writing, but may be selected
-; with "progzone"
-;
-; This feature can also easily detect false hangups. The symptoms of this is
-; being disconnected in the middle of a call for no reason.
-;
-;callprogress=yes
-;progzone=us
-;
-; FXO (FXS signalled) devices must have a timeout to determine whe there was a
-; hangup before the line was answered. This value can be tweaked to shorten
-; how long it takes before Zap considers a non-ringing line to have hungup.
-;
-;ringtimeout=8000
-;
-; For FXO (FXS signalled) devices, whether to use pulse dial instead of DTMF
-;
-;pulsedial=yes
-;
-; For fax detection, uncomment one of the following lines. The default is *OFF*
-;
-;faxdetect=both
-;faxdetect=incoming
-;faxdetect=outgoing
-;faxdetect=no
-;
-; Select which class of music to use for music on hold. If not specified
-; then the default will be used.
-;
-;musiconhold=default
-;
-; PRI channels can have an idle extension and a minunused number. So long as
-; at least "minunused" channels are idle, chan_zap will try to call "idledial"
-; on them, and then dump them into the PBX in the "idleext" extension (which
-; is of the form exten at context). When channels are needed the "idle" calls
-; are disconnected (so long as there are at least "minidle" calls still
-; running, of course) to make more channels available. The primary use of
-; this is to create a dynamic service, where idle channels are bundled through
-; multilink PPP, thus more efficiently utilizing combined voice/data services
-; than conventional fixed mappings/muxings.
-;
-;idledial=6999
-;idleext=6999 at dialout
-;minunused=2
-;minidle=1
-;
-; Configure jitter buffers in zapata (each one is 20ms, default is 4)
-;
-;jitterbuffers=4
-;
-; You can define your own custom ring cadences here. You can define up to 8
-; pairs. If the silence is negative, it indicates where the callerid spill is
-; to be placed. Also, if you define any custom cadences, the default cadences
-; will be turned off.
-;
-; Syntax is: cadence=ring,silence[,ring,silence[...]]
-;
-; These are the default cadences:
-;
-;cadence=125,125,2000,-4000
-;cadence=250,250,500,1000,250,250,500,-4000
-;cadence=125,125,125,125,125,-4000
-;cadence=1000,500,2500,-5000
-;
-; Each channel consists of the channel number or range. It inherits the
-; parameters that were specified above its declaration.
-;
-; For GR-303, CRV's are created like channels except they must start with the
-; trunk group followed by a colon, e.g.:
-;
-; crv => 1:1
-; crv => 2:1-2,5-8
-;
-;
-;callerid="Green Phone"<(256) 428-6121>
-;channel => 1
-;callerid="Black Phone"<(256) 428-6122>
-;channel => 2
-;callerid="CallerID Phone" <(256) 428-6123>
-;callerid="CallerID Phone" <(630) 372-1564>
-;callerid="CallerID Phone" <(256) 704-4666>
-;channel => 3
-;callerid="Pac Tel Phone" <(256) 428-6124>
-;channel => 4
-;callerid="Uniden Dead" <(256) 428-6125>
-;channel => 5
-;callerid="Cortelco 2500" <(256) 428-6126>
-;channel => 6
-;callerid="Main TA 750" <(256) 428-6127>
-;channel => 44
-;
-; For example, maybe we have some other channels which start out in a
-; different context and use E & M signalling instead.
-;
-;context=remote
-;sigalling=em
-;channel => 15
-;channel => 16
-
-;signalling=em_w
-;
-; All those in group 0 I'll use for outgoing calls
-;
-; Strip most significant digit (9) before sending
-;
-;stripmsd=1
-;callerid=asreceived
-;group=0
-;signalling=fxs_ls
-;channel => 45
-
-;signalling=fxo_ls
-;group=1
-;callerid="Joe Schmoe" <(256) 428-6131>
-;channel => 25
-;callerid="Megan May" <(256) 428-6132>
-;channel => 26
-;callerid="Suzy Queue" <(256) 428-6233>
-;channel => 27
-;callerid="Larry Moe" <(256) 428-6234>
-;channel => 28
-;
-; Sample PRI (CPE) config: Specify the switchtype, the signalling as either
-; pri_cpe or pri_net for CPE or Network termination, and generally you will
-; want to create a single "group" for all channels of the PRI.
-;
-; switchtype = national
-; signalling = pri_cpe
-; group = 2
-; channel => 1-23
-
-;
-
-; Used for distintive ring support for x100p.
-; You can see the dringX patterns is to set any one of the dringXcontext fields
-; and they will be printed on the console when an inbound call comes in.
-;
-;dring1=95,0,0
-;dring1context=internal1
-;dring2=325,95,0
-;dring2context=internal2
-; If no pattern is matched here is where we go.
-;signalling = fxo_ks
-;callerid = "Phone 1" <1001>
-;context=default
-;channel => 1
-;signalling = fxo_ks
-;callerid = "Phone 2" <1002>
-;context=default
-;channel => 2
-;signalling = fxo_ks
-;callerid = "Phone 3" <1003>
-;context=default
-;channel => 3
-;signalling = fxo_ks
-;callerid = "Phone 4" <1004>
-;context=default
-;channel => 4
-
-;group = 2
-;context = default
-;callerid = asreceived
-;signalling = fxs_ks
-;channel => 5-8
More information about the aadk-commits
mailing list