[svn-commits] tzafrir: trunk r2614 - /trunk/doc/
svn-commits at lists.digium.com
svn-commits at lists.digium.com
Sat Jun 9 17:19:38 MST 2007
Author: tzafrir
Date: Sat Jun 9 19:19:38 2007
New Revision: 2614
URL: http://svn.digium.com/view/zaptel?view=rev&rev=2614
Log:
* fxotune man page is up-to-date for 1.4.
* fxtest man page.
(crev. 2611)
* ó is non-printable on non-UTF-8 locales. Replaced with \['o] to make
lintian happy.
(rev. 2612)
Added:
trunk/doc/fxstest.8
- copied unchanged from r2612, branches/1.4/doc/fxstest.8
Modified:
trunk/doc/fxotune.8
trunk/doc/ztcfg.8
trunk/doc/ztmonitor.8
trunk/doc/zttool.8
Modified: trunk/doc/fxotune.8
URL: http://svn.digium.com/view/zaptel/trunk/doc/fxotune.8?view=diff&rev=2614&r1=2613&r2=2614
==============================================================================
--- trunk/doc/fxotune.8 (original)
+++ trunk/doc/fxotune.8 Sat Jun 9 19:19:38 2007
@@ -1,38 +1,149 @@
-.TH FXOTUNE 8 "September 10th, 2005" "Xorcom Rapid Asterisk" "Linux Programmer's Manual"
+.TH FXOTUNE "8" "9 June 2007" "asterisk" "System Manager's Manuals: Asterisk"
.SH NAME
-.B fxotune
-\(em automatically tune FXO channels on a Digium TDM400 card
+fxotune \- automatically tune zaptel FXO channels
.SH SYNOPSIS
.B fxotune -i
-.I <dialstr>
-\(em detect
-
-.B fxotune -s
-\(em load settings
-
+.I [options]
+- detect mode
+
+.B fxotune -d
+.I [ options ]
+- dump mode
+
+.B fxotune -s
+- Startup mode
+.SH
.SH DESCRIPTION
.B fxotune
-is a script that fine-tune parameters of the FXO modules of the TDM400
-card. Whene run in
+is a script that fine-tune parameters of the FXO modules of the
+card. It has three modes of operation:
+
+.I Detect mode (-i):
+it detects and tunes all the available FXO channels.
+It writes settings to a configuration file (/etc/fxotune.conf)
+from which it can be loaded (e.g: at startup) using -s .
+
+.I Dump mode (-d):
+Runs detection on a single Zaptel channel, and just dumps waveforms to
+.B fxotune_dump.vals
+is generated in the current directory.
+
+.I Startup mode (-s):
+fxotune just reads the settings from fxotune.conf into the FXO modules.
+
+You are advised to run fxotune on all FXO ports you have that support
+it and that are connected. Note that the tunning is affected by e.g.
+the physical parameters of the connection, and thus if it has been
+radically changed, you may need to re-run fxotune.
+
+FXOTune only works for the Digium TDM400P/800P/2400P cards and
+compatible and the Xorcom Astribank devices. Other cards (notably X100P
+cards and clones) do not have the hardware to support such tuning.
+
+The tuning process needs a clear line to do the tuning. In order to do
+that, it runs in cycles of the following: sets the line off-hook, dials
+a dial string (which should set the PSTN provider waiting for the next
+digit), and then starts tuning. It has a limited ammount of time for
+tuning before the PSTN gives up and gives a busy tone. So after a while
+it hangs up and starts a new cycle.
+
+.B fxotune
+has two operation modes: tune (-i) and set (-s). In the tune mode it
+generates /etc/fxotune.conf, and in the set mode it merely applies the
+parameters from fxotune.conf to device's ports.
+
+.SH OPTIONS
+The following options below except -v (verbose) affect only the
+detection process and hence apply only to the
.I detect
-mode (-i) it detects and tunes all the FXO channels of such cards. It
-needs a dial string after which the line(s) will give dial tone.
-
-It writes settings to a configuration file (/etc/fxotune.conf , name
-is hardwired) from which it can be loaded (e.g: at startup) using -s .
-
-
-.SH OPTIONS
-.B -i
-.RS
-.I dialstr
-Start detecting optimal settings.
-.I dialstr
-Is a number needed to dial to get a dial tone.
-The test can take several minutes, and must be performed when Asterisk
-is not running.
-
-For example:
+and
+.I dump
+modes.
+
+In addition, to maintain compatibility with older versions of fxotune,
+if in detect or dump mode there is a parameter with option before it, it
+is considered to be the
+.I dialstring
+parameter (-n).
+
+.B -b
+.I startdev
+.RS
+Start tuning from zaptel channel num. \fI startdev\fR: skip all previous
+channels. By default starting from channel 1.
+
+In dump mode (-d) this is the single channel that will be tested.
+.RE
+
+.B -e
+.I stopdev
+.RS
+Tune only up to zaptel channel num. \fI stopdev\fR: skip all previous
+channels. By default stopping at channel 252.
+
+In dump mode (-d) this parameter is ignored.
+.RE
+
+.B -l
+.I delay-to-silence
+.RS
+Time in seconds to wait after dialing the dial-string to get a clear line.
+The default is 0.
+before
+.RE
+
+.B -m
+.I silence-good-for
+.RS
+Time in seconds which states how long the PSTN will wait after we dialed
+the dial-string until it starts giving a busy tone. You can test this by
+connecting an analog phone to the line and dialing.
+
+The default is 18 (18 seconds).
+.RE
+
+.B -n
+.I dial-string
+.RS
+Digits to dial to the PSTN in order to get it stop its dialtone and
+waiting for the next digit.
+
+The default is "4" (sending just the digit 4). It should work in most
+cases. Again, this can be tested by connecting a phone to the PSTN line
+and dialing the dial-string.
+.RE
+
+.B -t
+.I detect-type
+.RS
+This option allows using the older detection method used by fxotune of
+zaptel 1.2. use
+.B -t 1
+for that older method. whereas
+.B -t 2
+(the default) uses the current method.
+
+This option only applies to detect mode (-i).
+.RE
+
+.B -v[vvvv]
+.RS
+Sets debugging on. The more v-s, the higher debug level.
+
+Note that: -vv -v will actually set debug level to 1 instead of 3.
+.RE
+
+.B -w
+.I wave-form
+.RS
+The default: -1, for multitone waveform. Alternatively: a frequency of a
+single tone.
+
+This option only applies to dump mode (-d).
+.RE
+
+
+.SH EXAMPLES
.RS
fxotune -i 9
.RE
@@ -52,6 +163,35 @@
configuration is loaded when
.B -s
is used.
+
+.SH NOTES
+Running fxotune takes approximately a minute per port. If you wish to only
+run fxotune for several ports, you can use the options -b and -e to set a
+specific range of ports. Another useful trick is to actually keep asterisk
+running, and only "destroy" the zaptel channels you wish to tune (zap
+destroy channel NNN): other channels will be used by Asterisk, and hence
+skipped. This can be useful if you have many FXO ports that are not connected.
+
+.B fxotune
+writes immedietly to
+.B /etc/fxotune.conf
+so if you stop it half-way, you may get a half-configured system. If you
+have already tuned your FXO channels and wish to test-run fxotune again,
+you are advised to backup /etc/fxotune.conf .
+
+The default for -m is 18 seconds. This asusmes that you get a clear line
+for at least 18 seconds. It is advised that you test that timeout earlier
+by connecting a phone to the FXO line, dialing 4 (or whatever dial string
+you put with -n) and see how much time of silence you have.
+
+If you connect your device to a PSTN provider that is not in the US, there
+is a similar operation you should apply before even getting to fxotune:
+setting the opermode. The opermode sets a number of country-specific
+parameters. For the Digium analog cards this is set through the kernel module
+parameter 'opermode' . For the Xorcom Astribank this is set through the
+variable 'opermode' in /etc/default/zaptel or /etc/sysconfig/zaptel .
+For valid values of this parameter, see
+/usr/share/asterisk/init_fxo_modes .
.SH SEE ALSO
ztcfg(8), zttool(8), ztmonitor(8), asterisk(8).
Modified: trunk/doc/ztcfg.8
URL: http://svn.digium.com/view/zaptel/trunk/doc/ztcfg.8?view=diff&rev=2614&r1=2613&r2=2614
==============================================================================
--- trunk/doc/ztcfg.8 (original)
+++ trunk/doc/ztcfg.8 Sat Jun 9 19:19:38 2007
@@ -50,7 +50,8 @@
zttool(8), ztmonitor(8), asterisk(8).
.SH "AUTHOR"
.PP
-This manual page was written by Santiago Ruano Rincón <santiago at unicauca.edu.co> for
+This manual page was written by Santiago Ruano Rinc\['o]n
+<santiago at unicauca.edu.co> for
the Debian system (but may be used by others). Permission is
granted to copy, distribute and/or modify this document under
the terms of the GNU General Public License, Version 2 any
Modified: trunk/doc/ztmonitor.8
URL: http://svn.digium.com/view/zaptel/trunk/doc/ztmonitor.8?view=diff&rev=2614&r1=2613&r2=2614
==============================================================================
--- trunk/doc/ztmonitor.8 (original)
+++ trunk/doc/ztmonitor.8 Sat Jun 9 19:19:38 2007
@@ -32,7 +32,8 @@
zttool(8), ztcfg(8), asterisk(8).
.SH "AUTHOR"
.PP
-This manual page was written by Santiago Ruano Rincón <santiago at unicauca.edu.co> for
+This manual page was written by Santiago Ruano Rinc\['o]n
+<santiago at unicauca.edu.co> for
the Debian system (but may be used by others). Permission is
granted to copy, distribute and/or modify this document under
the terms of the GNU General Public License, Version 2 any
Modified: trunk/doc/zttool.8
URL: http://svn.digium.com/view/zaptel/trunk/doc/zttool.8?view=diff&rev=2614&r1=2613&r2=2614
==============================================================================
--- trunk/doc/zttool.8 (original)
+++ trunk/doc/zttool.8 Sat Jun 9 19:19:38 2007
@@ -23,7 +23,8 @@
ztmonitor(8), asterisk (8).
.SH "AUTHOR"
.PP
-This manual page was written by Santiago Ruano Rincón <santiago at unicauca.edu.co> for
+This manual page was written by Santiago Ruano Rinc\['o]n
+<santiago at unicauca.edu.co> for
the Debian system (but may be used by others). Permission is
granted to copy, distribute and/or modify this document under
the terms of the GNU General Public License, Version 2 any
More information about the svn-commits
mailing list