<html>
<head>
<meta content="text/html; charset=ISO-8859-1"
http-equiv="Content-Type">
</head>
<body bgcolor="#FFFFFF" text="#000000">
<br>
<blockquote cite="mid:51252588.1@telenet.be" type="cite">
<meta content="text/html; charset=ISO-8859-1"
http-equiv="Content-Type">
<font face="Helvetica, Arial, sans-serif">Hello,<br>
<br>
what is the equivalent parameter of X in the
ConfBridge()-command ?<br>
<br>
How can you exit ConfBridge by pressing a digit ?<br>
<br>
<br>
Concerning MeetMe() :<br>
Verbosity is 25 and I still don't see anything on the console or
in the logs when pressing '0' (zero).<br>
<br>
<br>
Kind regards,<br>
Jonas.<br>
</font><br>
<br>
<div class="moz-cite-prefix">On 02/20/2013 03:32 PM, Rusty Newton
wrote:<br>
</div>
<blockquote cite="mid:8dbafdad-d7fd-41ec-a7db-2a37ed74dd35@zimbra"
type="cite">
<pre wrap="">----- Original Message -----
</pre>
<blockquote type="cite">
<pre wrap="">From: "Jonas Kellens" <a moz-do-not-send="true" class="moz-txt-link-rfc2396E" href="mailto:jonas.kellens@telenet.be"><jonas.kellens@telenet.be></a>
</pre>
</blockquote>
<blockquote type="cite">
<pre wrap="">But nothing happens when pressing 0 (zero).
</pre>
</blockquote>
<pre wrap="">Why not check the logs in /var/log/asterisk/full ?. Make sure you have the full log enabled in logger.conf and that you have VERBOSE,DEBUG,DTMF type messages going to it. You can also push those to the console and watch what happens when you press zero. On the console be sure to turn up verbosity with "core set verbose 5"
If you can't tell what is happening, post a pastebin link to the log and point out (via timestamp or otherwise) where you would expect to see the DTMF digit. Maybe someone will be able to take a look.
I'd also really recommend using ConfBridge which is newer than MeetMe. If you switch to ConfBridge I'd recommend an upgrade to the latest 1.8.X as well.
</pre>
</blockquote>
</blockquote>
<br>
<br>
<blockquote type="cite">
<pre>Please don't top post (<a rel="nofollow" href="https://www.asterisk.org/community/discuss">https://www.asterisk.org/community/discuss</a>). Also, you
didn't pastebin any debug, so I can't confirm that there is not some other
issue upon a possible DTMF reception.
If it is the case that Asterisk doesn't detect a DTMF 0 when you send it from
the endpoint, then you probably want to look at a SIP packet capture to verify
the endpoint is actually sending the DTMF to Asterisk. What you look for in the
capture or audio will depend on what kind of DTMF you are sending with the
endpoint.
Does Asterisk detect the digit 0 at any other time outside of MeetMe?
Can you setup an extension matching for 1234567890 and dial that?
Do you see DTMF debug for all those digits?
If you do end up trying ConfBridge - I've never used it in 1.8. Others have
made me aware that ConfBridge wasn't the best in 1.8, and that it's much better
in 10 or preferably 11.
--
Rusty Newton
OS Community Support Manager | Digium, Inc. | <a class="moz-txt-link-abbreviated" href="http://www.digium.com">www.digium.com</a>
Office/Cell/Fax: 256-428-6200 </pre>
</blockquote>
<br>
<br>
Hello,<br>
<br>
I've tried now from Cisco SPA 508G and from Yealink T-28 to exit
Meetme() by pressing '0' (zero) but no success.<br>
<br>
As I said, to log in I need to give password 12340 and that goes
very well ! Once inside the conference room, I can press any digit :
nothing happens. Nothing in the logs about DTMF being received.<br>
<br>
To exit the whole conferencing thing I can press # and that also
succeeds ! So I don't think it has anything to do with
DTMF-troubles.<br>
<br>
<br>
<br>
I've taken a pcap trace on the Yealink T-28. Where can I find the
DTMF ? I can filter SIP, but no DTMF. To check if they were well
send...<br>
<br>
<br>
<br>
<br>
Kind regards,<br>
Jonas.<br>
<br>
<br>
<br>
<br>
</body>
</html>