I finally got an answer on IRC, turns out the problem was callprogress=yes (a.k.a. screwupmycalls=yes). Changing it to no and dropping the r seemed to work. I'd like the feature to work properly, but it's more important that I'm able to actually make calls :)<div>
<br></div><div>I *am* now stuck with a long pause before I hear the outgoing ringing though. Not sure if there's anything I can do to tackle that one.</div><div><br><br><div class="gmail_quote">On 11 February 2013 21:32, Matthew Fredrickson <span dir="ltr"><<a href="mailto:creslin@digium.com" target="_blank">creslin@digium.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Hey,<br>
<br>
Just quickly glanced over your data... one problem you have is that you're passing the 'r' flag in your Dial() statement in extensions.conf. That would definitely cause you to have never ending ringback from the analog line (since answer supervision is often not present). You might try removing that and retry your outbound call test.<br>
<br>
Hope that helps a bit.<br>
<br>
Matthew Fredrickson<br>
Digium, Inc.<div class="im"><br>
<br>
On 2/11/13 10:54 AM, Kevin Wright wrote:<br>
</div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div class="im">
<br>
I forgot to add, cat /proc/dahdi/* yields:<br>
<br>
Span 1: WCTDM/4 "Wildcard TDM400P REV E/F Board 5" (MASTER)<br>
<br>
1 WCTDM/4/0 FXSKS (In use) (EC: MG2 - INACTIVE)<br>
2 WCTDM/4/1 FXOKS (EC: MG2 - INACTIVE)<br>
3 WCTDM/4/2 Reserved<br>
4 WCTDM/4/3 Reserved<br>
<br>
<br>
I'm not sure if that (in use) is correct when I'm not actively in a call.<br>
<br>
This is a very sensitive setup, as a home installation it absolutely<br>
*must* pass the gruelling "wife test", so I'm keen to see it up and<br>
running properly :)<br>
<br>
<br>
On 11 February 2013 16:50, Kevin Wright <<a href="mailto:kev.lee.wright@gmail.com" target="_blank">kev.lee.wright@gmail.com</a><br></div><div class="im">
<mailto:<a href="mailto:kev.lee.wright@gmail.com" target="_blank">kev.lee.wright@gmail.<u></u>com</a>>> wrote:<br>
<br>
<br>
I'm attempting to place an outgoing call over POTS/DAHDI, it dials<br>
without problem but the remote answer isn't tried.<br>
<br>
So far I've attempted:<br>
<br></div>
* Searching on google<br>
* Enabling full and verbose logging (including the debug option of<div class="im"><br>
the DAHDI module) - showing NO event at the time I answer on the<br>
remote phone a.k.a "my mobile"<br></div>
* Using another phone on the same line - it works<br>
* Receiving a call on that line - no problem<br>
* Logging DTMF - it shows digits dialled on my mobile, after I've<div class="im"><br>
answered, even whilst it seems to still be ringing locally<br></div>
* Looking on the wiki<br>
* Asking on IRC<div class="im"><br>
<br>
So far, I've found nothing that helps.<br>
<br>
A sample log output is here: <a href="http://pastebin.com/cprZSy9i" target="_blank">http://pastebin.com/cprZSy9i</a><br>
And my chan_dahdi.conf: <a href="http://pastebin.com/L7mBJ66Y" target="_blank">http://pastebin.com/L7mBJ66Y</a><br>
And dahdi system.conf: <a href="http://pastebin.com/6UQPVC9x" target="_blank">http://pastebin.com/6UQPVC9x</a><br>
also in modprobe.d/dahdi.conf: <a href="http://pastebin.com/5ZqtcZdj" target="_blank">http://pastebin.com/5ZqtcZdj</a><br>
<br>
*any* advice/suggestions at this point would be very much appreciated!<br>
<br>
<br>
<br></div></blockquote></blockquote></div><br>
</div>