<div class="gmail_quote"><br>Richard<div><span style><br></span></div><div><font face="arial, sans-serif">I tried to leave these fields empty. It did not work. Not appear IE74 in the debug.</font></div><div><font face="arial, sans-serif">The possibility exists that the carrier does not be sending?</font></div>
<div><font face="arial, sans-serif"><br></font></div><div>Att,<br>Rafael Saraiva<br><br><br>
<br><br><div class="gmail_quote">2012/2/17 Richard Mudgett <span dir="ltr"><<a href="mailto:rmudgett@digium.com" target="_blank">rmudgett@digium.com</a>></span><br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
I had not noticed that you switched to direct email earlier.<br>
<br>
----- Original Message -----<br>
> Switchtype: euroisdn<br>
><br>
><br>
> This is my chan_dadhi.conf<br>
><br>
> [trunkgroups]<br>
> trunkgroup=>1,16<br>
> spanmap=>1,1<br>
<br>
The trunkgroups section is only needed if you are using NFAS and<br>
its presence may cause issues for switches that do not support it.<br>
NFAS is not supported by euroisdn or qsig.<br>
<br>
After looking again at your traces, the STATUS messages are complaining<br>
about the channel id indicated by Asterisk. The trunk groups setup<br>
you have here is causing it.<br>
<br>
Just make this an empty section.<br>
<br>
><br>
><br>
> [channels]<br>
> language=pt_BR<br>
> hidecallerid=no<br>
> usecallerid=yes<br>
> callwaiting=yes<br>
> callwaitingcallerid=yes<br>
> threewaycalling=yes<br>
> transfer=yes<br>
> canpark=yes<br>
> cancallforward=yes<br>
> callreturn=yes<br>
> echocancel=yes<br>
> echocancelwhenbridged=no<br>
> callerid=asreceived<br>
> switchtype=euroisdn ;qsig<br>
> signalling=pri_cpe<br>
> context=PABX<br>
> facilityenable=yes<br>
> hidecalleridname=no<br>
> ;aoc_enable=s,d,e<br>
> imediate=yes<br>
> ;busydetect=yes<br>
> overlapdial=yes<br>
> inbanddisconnect=yes<br>
> priindication=inband ;outofband<br>
> nsf=none<br>
> ;qsigchannelmapping=logical<br>
> pridialplan=unknown<br>
> prilocaldialplan=unknown<br>
> ;internationalprefix=00<br>
> ;nationalprefix=55<br>
> ;localprefix=5551<br>
> ;privateprefix=55513205<br>
> ;unknownprefix=<br>
> service_message_support=yes<br>
> mohinterpret=default<br>
> discardremoteholdretrieval=yes<br>
> group=1<br>
> channel=>1-15,17-31<br>
><br>
><br>
> And system.conf:<br>
><br>
><br>
><br>
> loadzone=br<br>
> defaultzone=br<br>
><br>
><br>
><br>
><br>
> #span=1,1,0,cas,hdb3<br>
> #cas=1-15,17-31:1101<br>
><br>
><br>
> span=1,0,0,ccs,hdb3<br>
> dchan=16<br>
> bchan=1-15,17-31<br>
><br>
><br>
><br>
> Att,<br>
> Rafael Saraiva<br>
><br>
><br>
><br>
><br>
><br>
> 2012/2/17 Richard Mudgett < <a href="mailto:rmudgett@digium.com" target="_blank">rmudgett@digium.com</a> ><br>
><br>
><br>
> > I could not send attachments to the list.<br>
> > Att,<br>
> > Rafael Saraiva<br>
><br>
> You could have put the traces inline like you did the console<br>
> capture.<br>
> However, the attached files were oddly garbled in that lines were<br>
> duplicated. It looks like your network switch does not like the<br>
> PROCEEDING or ALERTING messages.<br>
><br>
> The SETUP message did not have any differences between a normal call<br>
> and a collect call that I could see. So there does not appear to be a<br>
> way to tell the calls apart.<br>
><br>
> What is the configured switch type?<br>
><br>
> Richard<br>
><br>
><br>
</blockquote></div><br></div>
</div><br>