<DIV><mailto:SIP ${EXTEN}@{SERADDRESS},60,tr><mailto:evert@poboxes.info>I'm not a big fan of Line Side for Asterisk applications.... the individual channels have to be reserved (reminds me of the "old" days in telephony) and I don't like that... rather make it a tie trunk and use ARS/AAR routing in the Definity... much more general application. This also makes routing on the Asterisk a lot simpler.</mailto:evert@poboxes.info></mailto:SIP></DIV>
<DIV><mailto:SIP ${EXTEN}@{SERADDRESS},60,tr><mailto:evert@poboxes.info></mailto:evert@poboxes.info></mailto:SIP> </DIV>
<DIV><mailto:SIP ${EXTEN}@{SERADDRESS},60,tr><mailto:evert@poboxes.info>Easy to make the changes.... will advise if desired.</mailto:evert@poboxes.info></mailto:SIP></DIV>
<DIV><mailto:SIP ${EXTEN}@{SERADDRESS},60,tr><mailto:evert@poboxes.info></mailto:evert@poboxes.info></mailto:SIP> </DIV>
<DIV><mailto:SIP ${EXTEN}@{SERADDRESS},60,tr><mailto:evert@poboxes.info>Mark</mailto:evert@poboxes.info></mailto:SIP></DIV>
<DIV><mailto:SIP ${EXTEN}@{SERADDRESS},60,tr><mailto:evert@poboxes.info> <BR>> isdn-pri/line-side, protocol b, and a I think were using a TN464 <BR>> card on the definity. I'll have to check on the card. We are <BR>> using pri_net singnaling and national is our switchtype in <BR>> asterisk. I'll try the changes and report back. Thank you so much!<BR>> <BR>> -CP<BR>> <BR>> ________________________________________<BR>> From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-<BR>> users-bounces@lists.digium.com] On Behalf Of mavince@optonline.net<BR>> Sent: Sunday, November 05, 2006 6:09 PM<BR>> To: asterisk-users@lists.digium.com<BR>> Subject: [asterisk-users] Definity Asterisk Caller ID Issue<BR>> <BR>> You should run the 4ESS protocol ("a" on the Definity command <BR>> "change DS1 board#) as the Definity may not send Display Name <BR>> for the NI-2 protocol (settings "b" or "d")<BR>> �<BR>> Remember to�make the Asterisk zapata settings consistent with <BR>> the Definity.<BR>> �<BR>> On the Definity trunk group form Page 1, change "Codeset to send <BR>> Display" to "0 (zero)", also make sure Outgoing Display is "y" . <BR>> On Page 2, make sure Send Name and Send Calling Number are "y".<BR>> �<BR>> Setting Send UCID = "n" as well as Send Codeset 6/7LAI = "n", <BR>> will clean up those Unknown IEs.<BR>> �<BR>> The Zaptel software only supports CodeSet 0 Information Elements <BR>> so the Display Name has to be� in Codeset 0.<BR>> �<BR>> Mark<BR>> <BR>> > > <BR>> > !! < Unknown IE 1544 (len = 6)<BR>> > <BR>> > !! Unknown IE 8 (cs6, Unknown Information Element)<BR>> > <BR>> > Progress Description: Calling equipment is non-ISDN<BR>> > <BR>> > TON: International Number<BR>> > <BR>> > <BR>> > <BR>> > <BR>> > <BR>> > xxx*CLI><BR>> > <BR>> > < [ 02 01 d4 d2 08 02 0a e6 05 04 03 90 90 a2 18 03 a1 83 8b <BR>> 1e <BR>> > 02 81 83<BR>> > 70 05 91 34 33 38 39 96 08 04 d0 35 30 80 ]<BR>> > <BR>> <BR>> <BR></DIV></mailto:evert@poboxes.info></mailto:SIP>