<br>
<br>
<br>
<table width=100%>
<tr valign=top>
<td>
<td><font size=1 face="sans-serif"><b>Andrew McRory <amcrory@linuxsys.com></b></font>
<br><font size=1 face="sans-serif">Sent by: asterisk-users-admin@lists.digium.com</font>
<p><font size=1 face="sans-serif">03/03/2004 04:11 PM</font>
<br><font size=1 face="sans-serif">Please respond to asterisk-users</font>
<br>
<td><font size=1 face="Arial"> </font>
<br><font size=1 face="sans-serif"> To: asterisk-users@lists.digium.com</font>
<br><font size=1 face="sans-serif"> cc: </font>
<br><font size=1 face="sans-serif"> Subject: Re: [Asterisk-Users] wct1xxp module and the T100P</font></table>
<br>
<br>
<br><font size=2 face="Courier New">On Wed, 3 Mar 2004 cveazey@blackhillsfiber.com wrote:<br>
<br>
> I'm having trouble turning up a PRI to a T100P. I've read on the Digium <br>
> FAQ's that once the wct1xxp module is loaded correctly, the LED on the <br>
> T100P will flash red. I believe I've loaded the module correctly because <br>
> both wct1xxp and zaptel are listed when I do the "lsmod" command. The LED <br>
> on the card does not flash on and off. Does anyone have any <br>
> recommendations on what I could be doing wrong?<br>
<br>
Switch type, line code, framing all matter. How about posting your config?<br>
<br>
<br>
-- <br>
Andrew McRory - President/CTO<br>
Linux Systems Engineers, Inc.<br>
PO BOX 3791<br>
Tallahassee, FL 32315<br>
(850)224-5737<br>
(850)294-7567<br>
<br>
_______________________________________________________________________________</font>
<br><font size=2 face="Courier New">Sure:</font>
<br>
<br><font size=2 face="Courier New">zaptel.conf:</font>
<br>
<br><font size=2 face="Courier New">span=1,1,0,esf,b8zs</font>
<br><font size=2 face="Courier New">bchan=1-23</font>
<br><font size=2 face="Courier New">dchan=24</font>
<br><font size=2 face="Courier New">loadzone = us</font>
<br><font size=2 face="Courier New">defaultzone=us</font>
<br>
<br><font size=2 face="Courier New">zapata.conf:</font>
<br>
<br><font size=2 face="Courier New">[channels]</font>
<br><font size=2 face="Courier New">context=cyperpri</font>
<br><font size=2 face="Courier New">switchtype=national</font>
<br><font size=2 face="Courier New">pridialplan=unknown</font>
<br><font size=2 face="Courier New">signalling=pri_cpe</font>
<br><font size=2 face="Courier New">channel=>1-23</font>
<br>
<br><font size=2 face="Courier New">Here's a question, though: does the wct1xxp module read from either zaptel.conf or zapata.conf when loaded?</font>
<br>
<br><font size=2 face="Courier New">Thanks!</font>
<br><font size=2 face="Courier New">chris</font>
<br>
<br>