[asterisk-users] How to bind to ipv4 & ipv6

Eric Wieling EWieling at nyigc.com
Fri Sep 27 11:30:38 CDT 2013


Sorry, I meant item d) which says and I quote "Listen on the IPv4 and IPv6 wildcards.  Example: bindaddr=::"  and "Note that using bindaddr=:: will show only a single IPv6 socket in netstat. . IPv4 is supported at the same time using IPv4-mapped IPv6"

-----Original Message-----
From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Bakko
Sent: Friday, September 27, 2013 12:28 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] How to bind to ipv4 & ipv6

This means i can't use IPv4 and IPv6 together.

Right?

El 27/09/2013 11:25, Eric Wieling escribió:
> >From sip.conf.sample included in your Asterisk source tree.  See item c) and the Note:
>
> ; With the current situation, you can do one of four things:
> ;  a) Listen on a specific IPv4 address.      Example: bindaddr=192.0.2.1
> ;  b) Listen on a specific IPv6 address.      Example: bindaddr=2001:db8::1
> ;  c) Listen on the IPv4 wildcard.            Example: bindaddr=0.0.0.0
> ;  d) Listen on the IPv4 and IPv6 wildcards.  Example: bindaddr=::
> ; (You can choose independently for UDP, TCP, and TLS, by specifying 
> different values for ; "udpbindaddr", "tcpbindaddr", and 
> "tlsbindaddr".) ; (Note that using bindaddr=:: will show only a single IPv6 socket in netstat.
> ;  IPv4 is supported at the same time using IPv4-mapped IPv6 
> addresses.) ; ; You may optionally add a port number. (The default is 
> port 5060 for UDP and TCP, 5061 ; for TLS).
> ;   IPv4 example: bindaddr=0.0.0.0:5062
> ;   IPv6 example: bindaddr=[::]:5062
> ;
> ; The address family of the bound UDP address is used to determine how 
> Asterisk performs ; DNS lookups. In cases a) and c) above, only A 
> records are considered. In case b), only ; AAAA records are 
> considered. In case d), both A and AAAA records are considered. Note, 
> ; however, that Asterisk ignores all records except the first one. In 
> case d), when both A ; and AAAA records are available, either an A or 
> AAAA record will be first, and which one ; depends on the operating system. On systems using glibc, AAAA records are given ; priority.
>
> udpbindaddr=0.0.0.0             ; IP address to bind UDP listen socket to (0.0.0.0 binds to all)
>                                  ; Optionally add a port number, 
> 192.168.1.1:5062 (default is port 5060)
>
>
>
>
>
> -----Original Message-----
> From: asterisk-users-bounces at lists.digium.com 
> [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Daniel 
> van den Berg
> Sent: Friday, September 27, 2013 12:18 PM
> To: asterisk-users at lists.digium.com
> Subject: Re: [asterisk-users] How to bind to ipv4 & ipv6
>
> Hi All,
>
> I dont really see a solution there to the problem, just that the matter was discussed?
>
> Can Asterisk or can it not listen for IPv4 & IPv6 addresses at the same time? I only see that there is mention that you must use the bindaddr=::
> for it to listen for IPv4 & IPv6 but when I do this my IPv4 connections drops.
>
> Thanks!
>
> On 09/27/2013 05:59 PM, Johan Wilfer wrote:
>> http://lists.digium.com/pipermail/asterisk-users/2013-March/278122.ht
>> m
>> l
>>
>> Google :-)
>>
>> /J
>>
>> 2013-09-27 17:47, Daniel van den Berg skrev:
>>> Hi Asghar,
>>>
>>> How do I search the site as I dont see a search bar anywhere...could 
>>> you please give me the link to the solution in the list or educate 
>>> me on how to search the site bar going through every thread one by one.
>>> :)
>>>
>>> Thanks!
>>>
>>> Regards,
>>> On 09/27/2013 04:43 PM, Asghar Mohammad wrote:
>>>> Hi,
>>>> Please Search the List there is already a post and solution.
>>>>
>>>>
>>>>
>>>> On Fri, Sep 27, 2013 at 3:58 PM, Daniel van den Berg 
>>>> <asterisk at suretel.co.za <mailto:asterisk at suretel.co.za>> wrote:
>>>>
>>>>      Hi All,
>>>>
>>>>      This is my 1st post so lets go.
>>>>
>>>>      What I need to achieve is the following. I have server with 
>>>> both
>>>> IPv4
>>>>      addresses and IPv6 addresses. The problem that I am encountering
>>>>      is that
>>>>      in the sip.conf I am having difficulties to bind to both the
>>>> IPv4 and
>>>>      IPv6 addresses.
>>>>
>>>>      Can someone please assist me in this regard as I need to connect
>>>>      another
>>>>      server to this server on IPv6 while the rest of the clients are
>>>>      connecting on IPv4.
>>>>
>>>>      I need to know how to get this working?
>>>>
>>>>      --
>>>>     
>>>> _____________________________________________________________________
>>>>      -- Bandwidth and Colocation Provided by 
>>>> http://www.api-digital.com --
>>>>      New to Asterisk? Join us for a live introductory webinar every
>>>> Thurs:
>>>>      http://www.asterisk.org/hello
>>>>
>>>>      asterisk-users mailing list
>>>>      To UNSUBSCRIBE or update options visit:
>>>>      http://lists.digium.com/mailman/listinfo/asterisk-users
>>>>
>>>>
>>>>
>>>>
>>>
>>>
>
> --
> _____________________________________________________________________
> -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs:
>                 http://www.asterisk.org/hello
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>     http://lists.digium.com/mailman/listinfo/asterisk-users
>


--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs:
               http://www.asterisk.org/hello

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users



More information about the asterisk-users mailing list