[asterisk-users] send the calls from to servers

Fri Dec 20 10:01:50 CST 2013

You should be asking Aheeva these questions.

Here is an untested sample dialplan which could be adapted.   If you need more info you should read the Asterisk Book.

Exten => _1NXXNXXXXXX,1,Dial(DAHDI/g1/${EXTEN})
Exten => same,n,GotoIf($["${DIALSTATUS" != "ANSWER" && ($["${DIALSTATUS" != "BUSY"]?failover)
Exten => same,n,Hangup
Exten => same,n(failover),Dial(SIP/otherserver/${EXTEN})
Exten => same,n,Hangup

"otherserver" would be the peer entry in sip.conf for your other server.

-----Original Message-----
From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Salaheddine Elharit
Sent: Friday, December 20, 2013 10:51 AM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] send the calls from to servers

i attached file my dialplan

2013/12/20 Salaheddine Elharit <salah.elharit200 at gmail.com>

	in attached file my dialplan 

	thanks and regards

	2013/12/20 Eric Wieling <EWieling at nyigc.com>

		You must write dialplan code to do what you want.  Assuming you are not using a GUI with Asterisk, post your dialplan used for outgoing calls.

		-----Original Message-----
		From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Salaheddine Elharit

		Sent: Friday, December 20, 2013 4:34 AM
		To: Asterisk Users Mailing List - Non-Commercial Discussion
		Subject: Re: [asterisk-users] send the calls from to servers

		hello
		thanks for your response

		i try to switch the provider in the same server without issue but my problem now i have 2 servers in the same network and with the same configuration

		iw want to use the group 2 of the server 1 and group 2 of server 2 for the same calls. and if group 2 of server 1 is down i can continue to use group 2 of server 2

		thanks and regards

		[trunkgroups]
		trunkgroup => 1,16
		spanmap => 1,1,1

		[channels]
		#include dahdi-channels.conf

		context=default
		hidecallerid=no
		callwaiting=yes
		usecallingpres=yes
		callwaitingcallerid=yes
		threewaycalling=yes
		transfer=yes
		canpark=yes
		cancallforward=yes
		callreturn=yes
		rxgain=0.0
		txgain=0.0
		immediate=yes
		echocancel=no
		dtmfmode=auto

		group=1
		switchtype=euroisdn
		signalling=pri_cpe
		callgroup=1
		;pickupgroup=1
		immediate=no
		channel => 1-15,17-31

		group=2
		callgroup=2
		switchtype=qsig
		signalling=pri_net
		callerid=5xxxxxxxx
		immediate=no
		channel => 32-46,48-52

		2013/12/19 Eric Wieling <EWieling at nyigc.com>

		        The basic idea is dial using your main outbound dahdi group, then check the value of HANGUPCAUSE, then if appropriate dial out using your secondary dahdi group.   This is a standard thing.  Check the mailing list archives and voip-info.org

		        See also the [stdexten] section of extensions.conf.sample

		        -----Original Message-----
		        From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Salaheddine Elharit

		        Sent: Thursday, December 19, 2013 1:32 PM
		        To: Asterisk Users Mailing List - Non-Commercial Discussion

		        Subject: Re: [asterisk-users] send the calls from to servers

		        i ask about outbound calls not inbound round-robin

		        best regards

		        2013/12/19 Eric Wieling <EWieling at nyigc.com>

		                Inbound call hunting is handled by your carrier, not Asterisk.

		                -----Original Message-----
		                From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Salaheddine Elharit
		                Sent: Thursday, December 19, 2013 12:52 PM
		                To: Asterisk Users Mailing List - Non-Commercial Discussion
		                Subject: [asterisk-users] send the calls from to servers

		                I have this scenario

		                In the first server 192.168.5.100 I have asterisk installed 1.4.43 and  one diguim card with 2 ports: in the first port connection for the provider X : the second port of diguim card  the connection of the provider Y

		                In the second server (the same configuration) 192.168.5.200 asterisk installed 1.4.43 and  one diguim card with 2 ports : the first port is empty the second port  the connection of the provider Y

		                My question how can I do in order to send the calls of the second providers from the port 2 server 1 and port 2 server 2 ()if one of them is down I continue to send the calls from the other

		                 Thanks and regards

		                --
		                _____________________________________________________________________
		                -- Bandwidth and Colocation Provided by http://www.api-digital.com --
		                New to Asterisk? Join us for a live introductory webinar every Thurs:
		                               http://www.asterisk.org/hello

		                asterisk-users mailing list
		                To UNSUBSCRIBE or update options visit:
		                   http://lists.digium.com/mailman/listinfo/asterisk-users

		        --
		        _____________________________________________________________________
		        -- Bandwidth and Colocation Provided by http://www.api-digital.com --
		        New to Asterisk? Join us for a live introductory webinar every Thurs:
		                       http://www.asterisk.org/hello

		        asterisk-users mailing list
		        To UNSUBSCRIBE or update options visit:
		           http://lists.digium.com/mailman/listinfo/asterisk-users

		--
		_____________________________________________________________________
		-- Bandwidth and Colocation Provided by http://www.api-digital.com --
		New to Asterisk? Join us for a live introductory webinar every Thurs:
		               http://www.asterisk.org/hello

		asterisk-users mailing list
		To UNSUBSCRIBE or update options visit:
		   http://lists.digium.com/mailman/listinfo/asterisk-users