[asterisk-users] Echo and static on PRI with errors

Steve Totaro stotaro at asteriskhelpdesk.com
Wed Jul 1 12:58:25 CDT 2009


On Wed, Jul 1, 2009 at 6:35 AM, Tom O'Connor <tom at twinhelix.org> wrote:
>
>
> On Wed, Jul 1, 2009 at 11:08 AM, Steve Totaro <stotaro at first-notification.com> wrote:
>>
>>
>> On Wed, Jul 1, 2009 at 5:58 AM, Tom O'Connor <tom at twinhelix.org> wrote:
>>>
>>>
>>> On Wed, Jul 1, 2009 at 10:49 AM, Marco Signorini <marcotasto at libero.it> wrote:
>>>>
>>>> Tom O'Connor wrote:
>>>>
>>>> On Wed, Jul 1, 2009 at 7:37 AM, Francesco Peeters <francesco at fampeeters.com> wrote:
>>>>>
>>>>> John F. Ervin wrote:
>>>>> > What do you do if you find things sharing interrupts (IRQ 11) in my
>>>>> > case with my X100P card.  I believe there is some sort of internal
>>>>> > audio card in my cheap slow PC.
>>>>> >
>>>>> Check the BIOS whether you can:
>>>>> Change the IRQ assignments
>>>>> Disable the extra hardware using the same IRQ
>>>>>
>>>>> Or otherwise try changing the slot it is in... I had very good results
>>>>> in the past swapping card around
>>>>>
>>>>> Good luck!
>>>>>
>>>>
>>>> I did a bit of investigation WRT the IRQ settings on this box.
>>>>
>>>> 00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3) (prog-if 20)
>>>>     Subsystem: Hewlett-Packard Company Device 3207
>>>>     Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 11
>>>> --
>>>> 01:05.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev b2)
>>>>     Subsystem: Hewlett-Packard Company Device 3207
>>>>     Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 11
>>>> --
>>>> 02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express (rev 11)
>>>>     Subsystem: Hewlett-Packard Company Device 3209
>>>>     Flags: bus master, fast devsel, latency 0, IRQ 11
>>>> --
>>>> 81:01.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
>>>>     Subsystem: Device 79fe:0001
>>>>     Flags: bus master, medium devsel, latency 64, IRQ 11
>>>>
>>>> So basically there's 2 network cards and a USB controller sharing IRQ 11 with the Openvox card.
>>>>
>>>> I wasn't able to find any settings in the bios to manually configure IRQ assignments :(
>>>>
>>>> Could someone tell me how to set which IRQ the ISDN card picks up?
>>>>
>>>> --
>>>> Tom O'Connor
>>>>
>>>> http://www.twinhelix.org
>>>> tom at twinhelix.org
>>>>
>>>> Hi,
>>>> Unfortunately is not always possible and it depends on how the mainboard was realized. For what I can understand a lot of producers decide to route only a subset of physical IRQ lines to the PCI slots (I think is something related to cost reduction) and to share it with other onboard peripherals.
>>>> This lets impossible to change the IRQ assignment for expansion cards.
>>>>
>>>> This is not always true and sometimes swapping add-on cards solves the problem.
>>>>
>>>> We had better results with cards based on new Digium technology or with Sangoma cards.
>>>>
>>> There is almost no room for manouvering in the HP bios.  There's no ability to disable stuff like parallel ports, or anything else really.
>>>
>>> I don't think i'd buy digium hardware again.  I'm already considering RMAing these cards and getting Sangoma ones.
>>>
>>>
>>> --
>>> Tom O'Connor
>>>
>>> http://www.twinhelix.org
>>> tom at twinhelix.org
>>>
>>
>> That is one option.  The new line Digium cards are on par with Sangoma as far as IRQ issues.
>>
>> I really like Sangoma's lifetime warranty though.  I don't think Digium has countered that bold move.
>>
>> I would try the RMA and if that doesn't work, you can always pickup a decent last year's model server at http://www.surpluscomputers.com/featured-hardware/cg-69/servers.html
>>
>> For a basic asterisk server or PBX with nothing special going on, any of these servers are more than enough, even overkill.
>>
>> No affiliation, I have to say the shipping is high and they are slow to ship but the prices are great, never had an issue with any of their boxen (dozens, knock on wood....)
>
> I don't really know what you mean about the new line Digium cards..  which models are in this "new line"?
>
> the server i'm using is hardly new, it's one of the older DL145s; so i don't think this would help much!
>
> I've tried swapping the card in the slots.  no help :(
>
>
>
>
>
> --
> Tom O'Connor
>
> http://www.twinhelix.org
> tom at twinhelix.org
>

Well I guess if I were you, I would stop posting "woe is me" to the
list and call Digium.

They do have support people just waiting for your call, you know?

If they cannot help, then buy a better server.  They are dirt cheap.
Cheaper than the time you are wasting.

I am not sure why you are opposed to taking suggestions and just
replying with negatives.

I expect your next reply to be "*SOLVED* Echo and static on PRI with errors"

But somehow I doubt it.

--
Thanks,
Steve Totaro
+18887771888 (Toll Free)
+12409381212 (Cell)
+12024369784 (Skype)



More information about the asterisk-users mailing list