[asterisk-users] Asterisk not picking up incoming calls from TDM400P

Fri Jun 6 13:36:13 CDT 2008

Nope, didn't help.

Doesn't the context declaration come *before* the channel assignment in 
zapata.conf?
It's working that way in our main Asterisk server.

regards,

Drew

Tim Nelson wrote:
> It looks like you may be missing a context declaration right after your "channel => 1" line. Try adding "context=incoming" right after that. 
>
> Tim Nelson
> Systems/Network Support
> Rockbochs Inc.
> (218)727-4332 x105
>
> ----- Original Message -----
> From: "Drew Gibson" <drew at oanda.com>
> To: "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users at lists.digium.com>
> Sent: Friday, June 6, 2008 12:37:47 PM GMT -06:00 US/Canada Central
> Subject: [asterisk-users] Asterisk not picking up incoming calls from TDM400P
>
> Hi,
>
> I am having some issues with a new server install in Singapore.
>
> Outbound calls work fine.
>
> Inbound calls are not picked up by Asterisk.
>
> Zaptel 1.2.25 and Asterisk 1.2.28 both built from source.
> libpri installed
>
> wctdm and zaptel load without error
>
> Jun  6 23:34:03 fs01 kernel: [211138.372933] Zapata Telephony Interface 
> Registered on major 196
> Jun  6 23:34:03 fs01 kernel: [211138.372937] Zaptel Version: 1.2.25
> Jun  6 23:34:03 fs01 kernel: [211138.372943] Zaptel Echo Canceller: KB1
> Jun  6 23:34:03 fs01 kernel: [211138.383639] Freshmaker version: 73
> Jun  6 23:34:03 fs01 kernel: [211138.384053] Freshmaker passed register test
> Jun  6 23:34:04 fs01 kernel: [211139.076180] Module 0: Installed -- AUTO 
> FXO (FCC mode)
> Jun  6 23:34:04 fs01 kernel: [211139.275847] Module 1: Installed -- AUTO 
> FXO (FCC mode)
> Jun  6 23:34:04 fs01 kernel: [211139.475514] Module 2: Installed -- AUTO 
> FXO (FCC mode)
> Jun  6 23:34:05 fs01 kernel: [211139.675182] Module 3: Installed -- AUTO 
> FXO (FCC mode)
> Jun  6 23:34:05 fs01 kernel: [211139.682518] Found a Wildcard TDM: 
> Wildcard TDM400P REV I (4 modules)
> Jun  6 23:34:08 fs01 kernel: [211142.686305] Registered tone zone 18 
> (Singapore)
> Jun  6 23:34:14 fs01 kernel: [211149.412565] -- Setting echo registers:
> Jun  6 23:34:14 fs01 kernel: [211149.412990] -- Set echo registers 
> successfully
> Jun  6 23:34:14 fs01 kernel: [211149.413005] -- Setting echo registers:
> Jun  6 23:34:14 fs01 kernel: [211149.413426] -- Set echo registers 
> successfully
> Jun  6 23:34:14 fs01 kernel: [211149.413435] -- Setting echo registers:
> Jun  6 23:34:14 fs01 kernel: [211149.413848] -- Set echo registers 
> successfully
> Jun  6 23:34:14 fs01 kernel: [211149.413861] -- Setting echo registers:
> Jun  6 23:34:14 fs01 kernel: [211149.414276] -- Set echo registers 
> successfully
> Jun  6 23:34:28 fs01 kernel: [211163.107241] Zaptel Transcoder support 
> loaded
>
>
> The one and only POTS line has been tuned with "fxotune and "fxotune -s" 
> has been run.
> ztmonitor shows incoming ring (volume peaks at 3-4000)
>
> No, nothing, nadda, zero response from Asterisk.
>
> Can anyone suggest a tool to help find the gap between zaptel and Asterisk?
>
> regards,
>
> Drew
>
>
> zaptel.conf:-
>
> fxsks=1-4
> ;(have tried fxsls=1-4 but no difference)
> loadzone=sg
> defaultzone=sg
>
>
> zapata.conf:-
>
> [channels]
> group=1
> context=incoming
> callprogress=no
> rxgain=2.0
> txgain=0.0
> immediate=no
> usecallerid=yes
> callerid=asreceived
> signalling=fxs_ks
> relaxdtmf=yes
> pickupgroup=1
> faxdetect=incoming
>
> channel => 1
>
>
> indications.conf:-
>
> [general]
> country=sg
>
> <---- Other countries snipped --->
>
> [sg]
>
> ; Singapore section borrowed from 
> http://csusap.csu.edu.au/~whaase01/itc308/asterisk/indications.conf
> description = Singapore
> ; Singapore
> ; Reference: 
> http://www.ida.gov.sg/idaweb/doc/download/I397/ida_ts_pstn1_i4r2.pdf
> ; Frequency specs are:   425 Hz +/- 20Hz; 24 Hz +/- 2Hz; modulation 
> depth 100%; SIT +/- 50Hz
> ringcadence = 400,200,400,2000
> dial        = 425
> ring        = 425*24/400,0/200,425*24/400,0/2000     ; modulation should 
> be 100%, not 90%
> busy        = 425/750,0/750
> congestion  = 425/250,0/250
> callwaiting = 425*24/300,0/200,425*24/300,0/3200
> stutter     = 
> !425/200,!0/200,!425/600,!0/200,!425/200,!0/200,!425/600,!0/200,!425/200,!0/200,!425/600,!0/200,!425/200,!0/200,!425/600,!0/200,425
> info        = 950/330,1400/330,1800/330,0/1000       ; not currently in 
> use acc. to reference
> dialrecall  = 425*24/500,0/500,425/500,0/2500        ; unspecified in 
> IDA reference, use repeating Holding Tone A,B
> record      = 1400/500,0/15000                       ; unspecified in 
> IDA reference, use 0.5s tone every 15s
> ; additionally defined in reference
> nutone      = 425/2500,0/500
> intrusion   = 425/250,0/2000
> warning     = 425/624,0/4376                         ; end of period 
> tone, warning
> acceptance  = 425/125,0/125
> holdinga    = !425*24/500,!0/500                     ; followed by holdingb
> holdingb    = !425/500,!0/2500
>
>
> [incoming]
> ; Added Answer statement for troubleshooting
> exten => s,1,Answer()
>
> include => office-incoming
> include => internal
>
> [office-incoming]
> ; OANDA Office incoming calls
> ignorepat => 9
> exten => s,1,Wait,1                     ; Waiting a little longer for CID
> exten => s,n,Answer                     ; Answer the line
> exten => s,n,Set(TIMEOUT(digit)=2)
> exten => s,n,Set(TIMEOUT(response)=10)
> exten => s,n,Set(TIMEOUT(absolute)=14400)
> ;exten => s,n,Goto(ivr_menu)
>
> <----- rest of extensions.conf snipped  ----->
>
>   

-- 
Drew Gibson

Systems Administrator
OANDA Corporation
www.oanda.com