[asterisk-users] Red Alarm TE420 with E1s - R2

Roger C. Beraldi Martins rogerberaldi at gmail.com
Tue Dec 4 03:06:14 CST 2007 

2007/12/4, Tzafrir Cohen <tzafrir.cohen at xorcom.com>:
> On Mon, Dec 03, 2007 at 10:51:43PM +0100, Philipp Kempgen wrote:
> > Richard Lyman wrote:
> >
> > > I have never noticed, does the output of ztcfg change is it set to E1?
> >
> > Yes. More channels. :)
>
> No. The channels listed in ztcfg -vv are the channels you wrote in
> zaptel.conf . By the time they are printed, there is still no guarantee
> that they actually exist on the system.
>
> Just try:
>
> ztcfg -vv -c <(echo fxsks=1-200)
>
> This should print the list of channels (but fail later) just as long as
> you have zaptel loaded.
>

Yes, I see the output for the ztcfg is de same after I put de jumpers closed.

>
> To see the difference, look at /proc/zaptel/1 . You'll now see there 31
> channels instead of 24 (33 lines instead of 26).
>


Now I can see de all channels for de E1 operation mode:

[root at asterisk1 ~]# cat /proc/zaptel/1
Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" HDB3/ RED

           1 TE4/0/1/1 CAS
            ...
          16 TE4/0/1/16
          17 TE4/0/1/17 CAS
           ...
          31 TE4/0/1/31 CAS

All outputs for /proc/zaptel/* look like this. I don't know why don't
appear any more "(In use)" in the end of each line. The 4th span is
unused.

The red alert still showing... and it's not good to me... :(

Now I'm talking with Technical support from teleco operator (Brasil
Telecom) to confirm de cable standard.


This is the output on dmesg when zaptel comes up:

Dec  4 16:14:30 asterisk1 kernel: Zapata Telephony Interface
Registered on major 196
Dec  4 16:14:30 asterisk1 kernel: Zaptel Version: 1.4.4
Dec  4 16:14:30 asterisk1 kernel: Zaptel Echo Canceller: MG2
Dec  4 16:14:31 asterisk1 kernel: Found TE4XXP at base address
48100000, remapped to f884a000
Dec  4 16:14:31 asterisk1 kernel: TE4XXP version c01a016a, burst ON,
slip debug: OFF
Dec  4 16:14:31 asterisk1 kernel: Octasic optimized!
Dec  4 16:14:31 asterisk1 kernel: FALC version: 00000005, Board ID: 00
Dec  4 16:14:31 asterisk1 kernel: Reg 0: 0x31299400
Dec  4 16:14:31 asterisk1 kernel: Reg 1: 0x31299000
Dec  4 16:14:31 asterisk1 kernel: Reg 2: 0xffffffff
Dec  4 16:14:31 asterisk1 kernel: Reg 3: 0x00000000
Dec  4 16:14:31 asterisk1 kernel: Reg 4: 0x00000001
Dec  4 16:14:31 asterisk1 kernel: Reg 5: 0x00000000
Dec  4 16:14:31 asterisk1 kernel: Reg 6: 0xc01a016a
Dec  4 16:14:31 asterisk1 kernel: Reg 7: 0x00001f00
Dec  4 16:14:31 asterisk1 kernel: Reg 8: 0x010200ff
Dec  4 16:14:31 asterisk1 kernel: Reg 9: 0x00fd0000
Dec  4 16:14:31 asterisk1 kernel: Reg 10: 0x0000004a
Dec  4 16:14:31 asterisk1 kernel: TE4XXP: Launching card: 0
Dec  4 16:14:31 asterisk1 kernel: TE4XXP: Setting up global serial parameters
Dec  4 16:14:31 asterisk1 kernel: Found a Wildcard: Wildcard TE420 (4th Gen)
Dec  4 16:14:34 asterisk1 kernel: About to enter spanconfig!
Dec  4 16:14:34 asterisk1 kernel: Done with spanconfig!
Dec  4 16:14:34 asterisk1 kernel: About to enter spanconfig!
Dec  4 16:14:34 asterisk1 kernel: Done with spanconfig!
Dec  4 16:14:34 asterisk1 kernel: About to enter spanconfig!
Dec  4 16:14:34 asterisk1 kernel: Done with spanconfig!
Dec  4 16:14:34 asterisk1 kernel: About to enter spanconfig!
Dec  4 16:14:34 asterisk1 kernel: Done with spanconfig!
Dec  4 16:14:34 asterisk1 kernel: Registered tone zone 20 (Brazil)
Dec  4 16:14:34 asterisk1 kernel: About to enter startup!
Dec  4 16:14:34 asterisk1 kernel: TE4XXP: Span 1 configured for CAS/HDB3
Dec  4 16:14:34 asterisk1 kernel: timing source auto card 0!
Dec  4 16:14:34 asterisk1 kernel: wct4xxp: Setting yellow alarm on span 1
Dec  4 16:14:34 asterisk1 kernel: timing source auto card 0!
Dec  4 16:14:34 asterisk1 kernel: SPAN 1: Primary Sync Source
Dec  4 16:14:34 asterisk1 kernel: VPM400: Not Present
Dec  4 16:14:34 asterisk1 kernel: VPM450: Not Present
Dec  4 16:14:34 asterisk1 kernel: Completed startup!
Dec  4 16:14:34 asterisk1 kernel: About to enter startup!
Dec  4 16:14:34 asterisk1 kernel: TE4XXP: Span 2 configured for CAS/HDB3
Dec  4 16:14:34 asterisk1 kernel: wct4xxp: Setting yellow alarm on span 2
Dec  4 16:14:34 asterisk1 kernel: timing source auto card 0!
Dec  4 16:14:34 asterisk1 kernel: VPM400: Not Present
Dec  4 16:14:34 asterisk1 kernel: VPM450: Not Present
Dec  4 16:14:34 asterisk1 kernel: Completed startup!
Dec  4 16:14:34 asterisk1 kernel: About to enter startup!
Dec  4 16:14:34 asterisk1 kernel: TE4XXP: Span 3 configured for CAS/HDB3
Dec  4 16:14:34 asterisk1 kernel: wct4xxp: Setting yellow alarm on span 3
Dec  4 16:14:34 asterisk1 kernel: timing source auto card 0!
Dec  4 16:14:34 asterisk1 kernel: VPM400: Not Present
Dec  4 16:14:34 asterisk1 kernel: VPM450: Not Present
Dec  4 16:14:34 asterisk1 kernel: Completed startup!
Dec  4 16:14:34 asterisk1 kernel: About to enter startup!
Dec  4 16:14:34 asterisk1 kernel: TE4XXP: Span 4 configured for CAS/HDB3
Dec  4 16:14:34 asterisk1 kernel: wct4xxp: Setting yellow alarm on span 4
Dec  4 16:14:34 asterisk1 kernel: timing source auto card 0!
Dec  4 16:14:34 asterisk1 kernel: VPM400: Not Present
Dec  4 16:14:34 asterisk1 kernel: VPM450: Not Present
Dec  4 16:14:34 asterisk1 kernel: Completed startup!





> --
>                Tzafrir Cohen
> icq#16849755              jabber:tzafrir.cohen at xorcom.com
> +972-50-7952406           mailto:tzafrir.cohen at xorcom.com
> http://www.xorcom.com  iax:guest at local.xorcom.com/tzafrir
>
> _______________________________________________
> --Bandwidth and Colocation Provided by http://www.api-digital.com--
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
>


-- 
Atenciosamente,

Roger C. Beraldi Martins
Fone: 41-8828-7068

More information about the asterisk-users mailing list