[asterisk-users] Blind transfer 3/4 digits

[Ronald Wiplinger]

David Gagnon wrote:
> Ronald,
>
> 	You seem to be a little bit angry about VoIP. If so, I could give
> you my old Nortel system. Does this would make you happy?
>
> David
>
>   

David,

I am not angry about VoIP, but please send my your old Nortel system !!!!!

I just do not understand why I can DIAL 601 and 6014, but not use blind 
transfer. Is the question too difficult?

I am sure there is somewhere a switch to say, wait two seconds (as for 
dialing) before you assume it is a complete number.
It is also strange that snom phone can do it correct, because it uses 
the ok key.


> -----Message d'origine-----
> De : asterisk-users-bounces at lists.digium.com
> [mailto:asterisk-users-bounces at lists.digium.com] De la part de Ronald
> Wiplinger
> Envoyé : 2 septembre 2006 04:20
> À : Asterisk Users Mailing List - Non-Commercial Discussion
> Objet : Re: [asterisk-users] Blind transfer 3/4 digits
>
> Anthony Rodgers wrote:
>   
>> With respect, the problem is with your numbering plan......
>>
>>     
>
>   

This answer is therefore totally nonsense !!! (With all respect!!!)


Both answers have actually not lead to any step further, but to more 
messages. I use to refer to such answers as NON-ANSWERS.
Please only reply if and really only if you know a solution for the 
problem! Thanks for your understanding.

bye

Ronald - again, I am not angry at all.
> WHERE do you see a problem in the numbering plan?????
> I see the problem in ASTERISK, because it does not wait for the last 
> digit!!!
> Where can I set that it waits for it?
>
> The beauty on voip IS that you can have different length and 
> overlapping, ....
>
> bye
>
> Ronald
>   
>> CP
>>
>> On 1-Sep-06, at 10:37 PM, Ronald Wiplinger wrote:
>>
>>     
>>> I found a problem in blind transfer:
>>>
>>> I have an extension number 601 and I have an extension 6014 !!!!
>>>
>>> If I get a call on 615 (snom) and transfer to 6014 it works, since snom
>>> requires me to hit "ok"
>>>
>>> If I get a call on 601 and transfer to 6014, than 601 will get the busy
>>> signal and I hang up as usually with transfer.
>>> Howerver the caller get the announcements: I could not get that, ....
>>>
>>> What could be the problem ?
>>>
>>> bye
>>>
>>> Ronald
>>>
>>>
>>> _______________________________________________
>>> --Bandwidth and Colocation provided by Easynews.com --
>>>
>>> asterisk-users mailing list
>>> To UNSUBSCRIBE or update options visit:
>>>    http://lists.digium.com/mailman/listinfo/asterisk-users
>>>
>>>       
>> _______________________________________________
>> --Bandwidth and Colocation provided by Easynews.com --
>>
>> asterisk-users mailing list
>> To UNSUBSCRIBE or update options visit:
>>   http://lists.digium.com/mailman/listinfo/asterisk-users
>>
>>
>>
>> ---
>> avast! Antivirus: Inbound message clean.
>> Virus Database (VPS): 0635-4, 2006/09/01
>> Tested on: 2006/9/2 ¤U¤È 03:52:00
>> avast! - copyright (c) 1988-2006 ALWIL Software.
>> http://www.avast.com
>>
>>
>>
>>
>>     
>
>
>   


-- 
Ronald Wiplinger  (CEO of ELMIT)
http://www.elmit.com  http://voip.elmit.com  http://e-paper.elmit.com 
Tel. (M) +886.939.775.516  (O) +886.2.2835.7765 (ENUM)   or FWD 511208
- I'm a SpamCon Foundation Member, #694, Verify it at http://www.spamcon.org

PS: Spam prevention!
Our system is protected with a spam prevention program. 
If you send us an e-mail, our system will send you a confirmation message back. Just reply to this confirmation message please. 
After receiving this confirmation message, our system will send the hold message (one) and all future messages (after the received confirmation message) to me without asking you again.