[asterisk-users] No Dialtone

[Rich Adamson]

If you've messed up in connecting telephone lines to the wrong module, 
the ringing voltage sent to a fxs module will destroy it. You would need 
to replace the module.



Eddie Johnson Jr wrote:
> Yes, I have and I received the following:
> 
> In zapata.conf your first two channels should be fxs_ks because the first
> two modules are FXO mdoules. Your last two channels should be fxo_ks because
> the second two modules are FXS modules.
> 
> For the TDM400P(TDM 22) the FXS modules work with the phone.  The 3 port is
> for the line.  So I unplugged it from port 3, and plugged the analog phone
> in port 1, made the changes to the channels and set immediate=no, restart
> the server and activated asterisk.  Nothing, my friend.
> 
> Any more suggestions,
> 
> Ed
> 
> -----Original Message-----
> From: asterisk-users-bounces at lists.digium.com
> [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Francesco
> Francesconi
> Sent: Friday, October 06, 2006 10:23 AM
> To: Asterisk Users Mailing List - Non-Commercial Discussion
> Subject: Re: [asterisk-users] No Dialtone
> 
> Did you set immediate=no in zapata.conf?
> 
> Francesco
> 
> Eddie Johnson Jr wrote:
>>  
>>
>> Hello,
>>
>>  
>>
>> I have the following setup:
>>
>>  
>>
>> 1. Ubuntu Dapper Server 6.06 plus latest patches
>>
>>  
>>
>> 2. Asterisk 1.2.11
>>
>>  
>>
>> 3. libpri 1.2.3
>>
>>  
>>
>> 4. Zaptel 1.2.8
>>
>>  
>>
>> 5. Digium TDM22 (TDM400P)
>>
>>  
>>
>> 6. Analog phone plugged in port 3
>>
>>  
>>
>> 7. The wctdm, zaptel modules load at startup, I type asterisk as root and
>>
>> it is activated.
>>
>>  
>>
>> 8. I check the Channel Map and I have the following:
>>
>>  
>>
>>  
>>
>> Channel map:
>>
>>  
>>
>> Channel 01: FXO Kewlstart (Default) (Slaves: 01)
>>
>> Channel 02: FXO Kewlstart (Default) (Slaves: 02)
>>
>> Channel 03: FXS Kewlstart (Default) (Slaves: 03)
>>
>> Channel 04: FXS Kewlstart (Default) (Slaves: 04)
>>
>>  
>>
>> 4 channels configured.
>>
>>  
>>
>> I can ssh into the server and remotely connect to the server. Great!
>> The card is not connected to an outside line as of yet but I have no
>> dialtone on the phone. I spoke with a rep. at digium and was told a
>> dialtone should be there.
>>
>>  
>>
>> Zaptel.conf :
>>
>>  
>>
>>  
>>
>> loadzone=us
>>
>> defaultzone=us
>>
>> fxoks=1,2
>>
>> fxsks=3,4
>>
>>  
>>
>> Zapata.conf:
>>
>>  
>>
>> ;FXS Modules
>>
>> signalling=fxo_ks
>>
>> channel => 1,2
>>
>> ;
>>
>> ;FXO Modules
>>
>> signalling=fxs_ks
>>
>> channel => 3,4
>>
>>  
>>
>> I made sure the card is not sharing an IRQ, I checked the hard drive
>> and all is well.  I load zttool and get the following:
>>
>>  
>>
>> cat /proc/zaptel/*
>>
>> Span 1: WCTDM/0 "Wildcard TDM400P REV I Board 1"
>>
>>  
>>
>> 1 WCTDM/0/0
>>
>> 2 WCTDM/0/1
>>
>> 3 WCTDM/0/2
>>
>> 4 WCTDM/0/3
>>
>>  
>>
>> Any suggestions?
>>
>>  
>>
>> Ed
>>
>>  
>>
>> ------------------------------------------------------------------------
>>
>> _______________________________________________
>> --Bandwidth and Colocation provided by Easynews.com --
>>
>> asterisk-users mailing list
>> To UNSUBSCRIBE or update options visit:
>>    http://lists.digium.com/mailman/listinfo/asterisk-users
>>   
> 
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
> 
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
> 
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
> 
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users