[asterisk-users] No Dialtone

[Eddie Johnson Jr]

Yes, I have and I received the following:

In zapata.conf your first two channels should be fxs_ks because the first
two modules are FXO mdoules. Your last two channels should be fxo_ks because
the second two modules are FXS modules.

For the TDM400P(TDM 22) the FXS modules work with the phone.  The 3 port is
for the line.  So I unplugged it from port 3, and plugged the analog phone
in port 1, made the changes to the channels and set immediate=no, restart
the server and activated asterisk.  Nothing, my friend.

Any more suggestions,

Ed

-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Francesco
Francesconi
Sent: Friday, October 06, 2006 10:23 AM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [asterisk-users] No Dialtone

Did you set immediate=no in zapata.conf?

Francesco

Eddie Johnson Jr wrote:
>
>  
>
> Hello,
>
>  
>
> I have the following setup:
>
>  
>
> 1. Ubuntu Dapper Server 6.06 plus latest patches
>
>  
>
> 2. Asterisk 1.2.11
>
>  
>
> 3. libpri 1.2.3
>
>  
>
> 4. Zaptel 1.2.8
>
>  
>
> 5. Digium TDM22 (TDM400P)
>
>  
>
> 6. Analog phone plugged in port 3
>
>  
>
> 7. The wctdm, zaptel modules load at startup, I type asterisk as root and
>
> it is activated.
>
>  
>
> 8. I check the Channel Map and I have the following:
>
>  
>
>  
>
> Channel map:
>
>  
>
> Channel 01: FXO Kewlstart (Default) (Slaves: 01)
>
> Channel 02: FXO Kewlstart (Default) (Slaves: 02)
>
> Channel 03: FXS Kewlstart (Default) (Slaves: 03)
>
> Channel 04: FXS Kewlstart (Default) (Slaves: 04)
>
>  
>
> 4 channels configured.
>
>  
>
> I can ssh into the server and remotely connect to the server. Great!
> The card is not connected to an outside line as of yet but I have no
> dialtone on the phone. I spoke with a rep. at digium and was told a
> dialtone should be there.
>
>  
>
> Zaptel.conf :
>
>  
>
>  
>
> loadzone=us
>
> defaultzone=us
>
> fxoks=1,2
>
> fxsks=3,4
>
>  
>
> Zapata.conf:
>
>  
>
> ;FXS Modules
>
> signalling=fxo_ks
>
> channel => 1,2
>
> ;
>
> ;FXO Modules
>
> signalling=fxs_ks
>
> channel => 3,4
>
>  
>
> I made sure the card is not sharing an IRQ, I checked the hard drive
> and all is well.  I load zttool and get the following:
>
>  
>
> cat /proc/zaptel/*
>
> Span 1: WCTDM/0 "Wildcard TDM400P REV I Board 1"
>
>  
>
> 1 WCTDM/0/0
>
> 2 WCTDM/0/1
>
> 3 WCTDM/0/2
>
> 4 WCTDM/0/3
>
>  
>
> Any suggestions?
>
>  
>
> Ed
>
>  
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
>   

_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users