[asterisk-users] wip5000 roaming

[Andrew Joakimsen]

Yes, same WEP key, SSID and channel for all the AP.

On 11/9/06, Altus Snyman <altus at stormcorp.co.za> wrote:
>
>  Everything is working beside roaming
>
> Yes im using encryption, should I turn it off, or uses the same wep key,
> and same ssid
>
> Should I then also just add 1 config with 1 access point , not 2?
>
>
>  ------------------------------
>
> *From:* asterisk-users-bounces at lists.digium.com [mailto:
> asterisk-users-bounces at lists.digium.com] *On Behalf Of *Andrew Joakimsen
> *Sent:* Thursday, November 09, 2006 8:53 PM
> *To:* Asterisk Users Mailing List - Non-Commercial Discussion
> *Subject:* Re: [asterisk-users] wip5000 roaming
>
>
>
> Disable WDS but set all the AP to the same channel and same SSID and then
> make sure they are connected to the same LAN (IE: no NAT on the AP). Are you
> using encryption?
>
> Something like:
>
> Try RxLevel -60
> PreRoaming Enable RxLevel -75
> Try over TxErrcnt 15
> Try Over RxError Count 10
>
> Play with the PreRoaming mode, see if it does help? It should however you
> could notice a drop in battery life.
>
> Would be a good place to start with your settings, adjust from there.  I
> would like to hear your results with these phones, is everything working
> great besides the roaming?
>
> On 11/9/06, *Altus Snyman* <altus at stormcorp.co.za> wrote:
>
> Good day all
>
> I cant get my WIP 5000 to roam 100%
>
> I have 2 access points, different SSI's
>
> I make a config1 and config2 on the phone, each for the different SSID's(A
> & B)
>
> Im standing next to A and I walk to B, but…the phone does not want to
> change its signal to B, it still keeps the bad signal from A
>
> If I power A down, it will switch to B, if I switch A back on and go stand
> next to it, it will still keep B's signal
>
> We got some wireless specialist's in and they set up WDS for us, in other
> words, you add 1 SSID for both access point
>
> IT works for windows, but not for the phone!
>
> Can anyone help, or give a bit more explanation on the roaming settings on
> the webconfig
>
>
>
> Try RxLevel (-103~0)
>
> PreRoaming Enable RxLevel (-103~0)
>
> Try Over TxError Count (0~10000)
>
> Try Over RxError Count (0~10000)
>
> Level Diff Higher Than Curr Site (0~255)
>
> Use Refresh PreRoaming
>
> Enable PreRoaming On Association
>
> PreRoaming Mode
>
> PreRoaming Refresh Interval (0:Disable, 0~3600)
>
>
>
>
>
> Thanks
>
> Altus
>
>
>
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061109/81c31a02/attachment.htm