[Asterisk-Users] OT: AudioCodes MP124-C/FSX/AC/SIP

[The VoIP Connection]

FXS or FXO?

Michael Crown
Managing Partner
www.thevoipconnection.com
321.989.6728 ext. 611
sip:611 at voiceserver.thevoipconnection.com
 

> -----Original Message-----
> From: William Piper [mailto:billy at kersting.com] 
> Sent: Wednesday, May 24, 2006 6:27 PM
> To: 'Asterisk Users Mailing List - Non-Commercial Discussion'
> Subject: RE: [Asterisk-Users] OT: AudioCodes MP124-C/FSX/AC/SIP
> 
> Sorry to hijack your thread.
> 
> Reading these posts made me grab my old MP-104 & try again to 
> get it working with asterisk.  I bought it a while ago off 
> eBay & never could get it to register. 
> 
> Does anyone have an example ini file for the MP-1XX that I 
> could look at & figure out what I am configuring wrong on this box?
> 
> Thanks,
> 
> bp
> 
> -----Original Message-----
> From: asterisk-users-bounces at lists.digium.com
> [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of 
> Jerry Jones
> Sent: Wednesday, May 24, 2006 6:04 PM
> To: Asterisk Users Mailing List - Non-Commercial Discussion
> Subject: Re: [Asterisk-Users] OT: AudioCodes MP124-C/FSX/AC/SIP
> 
>  From my copy of the manual
> 
> 
> MP-1xx SIP User's Manual  36 Document #: LTRT-65404 You can 
> use the 'Reset' button to restore the MP-1xx networking 
> parameters to their factory default values (described in 
> Table  4-1) and to reset the username and password.
> Note that the MP-1xx returns to the software version burned 
> in flash.  
> This process also restores
> the MP-1xx parameters to their factory settings, therefore 
> you must load your previously backed- up ini file, or the 
> default ini file (received with the software kit) to set them 
> to their correct values.
> To restore networking parameters to their initial state, take these 6
> steps:
> 1. Disconnect the MP-1xx from the power and network cables.
> MP-1xx SIP User's Manual 4. Getting Started 2. Reconnect the 
> power cable; the gateway is powered up. After approximately 
> 45 seconds the Ready LED turns to green and the Control LED 
> blinks for about 3 seconds.
> 3. While the Control LED is blinking, press shortly on the 
> reset button (located on the left side of the front panel); 
> the gateway resets a second time and is restored with factory 
> default parameters (username: "Admin", password: "Admin").
> 4. Reconnect the network cable.
> 5. Assigning the MP-1xx IP address (refer to Section  4.1 on page 35).
> 6. Load your previously backed-up ini file, or the default 
> ini file (received with the software kit).
> To load the ini file via the Embedded Web Server, refer to Section   
> 5.9.2.1 on page 120.
> 
> 
> 
> 
> On May 24, 2006, at 3:00 PM, Erick Perez wrote:
> 
> > Just a question, has anyone knows how to blank or factory reset an 
> > AudioCodes MP124-C/FSX/AC/SIP unit (it's a 24 FSX to SIP unit).
> > I purchased them second-handed with no manuals (thank god for the
> > internet!!) but i guess the pdf manual I have does not have the 
> > section of factory-reset.
> >
> > Also, any sucess stories with:
> > AudioCodes MP124-C/FSX/AC/SIP 
> <--->Asterisk<---internet<--->Vonage   
> > setups?
> >
> > Thanks,
> >
> >
> > --
> >
> > -------------------------------------------
> > Erick Perez
> > Linux User 376588
> > http://counter.li.org/  (Get counted!!!) Panama, Republic of Panama 
> > _______________________________________________
> 
> 
> 
>