[Asterisk-Users] ISDN, TE205P, I'm goind crazy :>

[Eric "ManxPower" Wieling]

ESF/B8ZS is a T-1 config.

azyuky wrote:
> Hi Josue and list,
> 
> This is part of my dmesg log. Also one other thing, I don't know why the red light
> on span/port 1 of my card keep flashing.. is it normal that way? Or it's supposed to
> mean something? Obviously I have no experience with ISDN before so this is my very
> first try. 
> 
> Found TE2XXP at base address e7001000, remapped to e001a000
> TE2XXP version c01a0164, burst OFF, slip debug: OFF
> FALC version: 00000005, Board ID: 00
> Reg 0: 0x1e6ab400
> Reg 1: 0x1e6ab000
> Reg 2: 0xffffffff
> Reg 3: 0x00000000
> Reg 4: 0x00000000
> Reg 5: 0x00000000
> Reg 6: 0xc01a0164
> Reg 7: 0x00001000
> Reg 8: 0x00000000
> Reg 9: 0x00ff0000
> Reg 10: 0x00000000
> TE2XXP: Launching card: 0
> TE2XXP: Setting up global serial parameters
> Found a Wildcard: Wildcard TE205P 
> About to enter spanconfig!
> Done with spanconfig!
> Registered tone zone 
> About to enter startup!
> TE2XXP: Span 1 configured for ESF/B8ZS
> wct2xxp: Setting yellow alarm on span 1
> 2G: Got interrupt, status = 0000000d, GIS = 0081
> SPAN 1: Primary Sync Source
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> VPM: Not Present
> Completed startup!
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> 2G: Got interrupt, status = 0000000a, GIS = 0080
> About to enter spanconfig!
> About to enter startup!
> TE2XXP: Span 1 configured for ESF/B8ZS
> SPAN 1: Primary Sync Source
> Completed startup!
> Registered tone zone 
> About to enter spanconfig!
> About to enter startup!
> TE2XXP: Span 1 configured for ESF/B8ZS
> SPAN 1: Primary Sync Source
> Completed startup!
> Registered tone zone 
> About to enter spanconfig!
> About to enter startup!
> TE2XXP: Span 1 configured for ESF/B8ZS
> SPAN 1: Primary Sync Source
> Completed startup!
> Registered tone zone 
> 
> 
> --- Josué Conti <josueconti at gmail.com> wrote:
> 
>> Hi, test with dmesg and past in list the log´s
>>
>> Regards
>>
>> Josué
>>
>> 2006/5/10, azyuky <azyuky at yahoo.com>:
>>> Hi guys,
>>>
>>> Currently I just purchased the TE205P for the installation of my ISDN30
>>> setup. I
>>> compiled, setup the card correctly I think. When I do the ztcfg -vvv it
>>> shows all 31
>>> channels clear, with 30 bchannels using for voice ranging from 1-15,
>>> 17-31, and 16
>>> is the dchannel. However, when I do a cat /proc/zaptel/1 I see only 24
>>> channels
>>> configured, and then, when I do a cat /proc/zaptel/2 I see the rest 7
>>> channels. I
>>> setup the jumper correctly all closed to use the card in E1 mode.. I'm not
>>> sure what
>>> I did wrong here but the card should just display all 31 channels on span
>>> 1
>>> (/proc/zaptel/1) instead of spreading it accross to the second span?
>>>
>>> Help is appreciated. Thank you.

-- 
Now accepting new clients in Birmingham, Atlanta, Huntsville, 
Chattanooga, and Montgomery.