[Asterisk-Users] help on mfc/r2

Melcon Moraes levelz at terra.com.br
Sun Mar 26 22:09:12 MST 2006


Well well, 

This is not right at all. You should have like 1001 for TxABCD and 1011
for RxABCD.

That's why you are getting blocked. Something called my attention:
Bipolar Violation: you have some of it, which confirms that there's
something wrong.

Indeed, your call file is ok. That's why I asked you about calling some
extensions inside Alcatel box from a sip and/or iax2 phone.

Question: if you have PRI, why are you using R2?
Sugestion: check Alcatel's setup for this card. On Alcatel side, do you
have any alarms or errors?

BTW, do you use any kind of IM?

[]'s
MM

 -----Original Message-----
From:   Krzysztof Drewicz <drewicz at citicom.pl>
To:     Asterisk Users Mailing List - Non-Commercial Discussion <asterisk-users at lists.digium.com>
Cc:     
Sent:  Mon, 27 Mar 2006 02:49:47 +0200
Delivered:  Sun,  26 Mar 2006 18:47:47 
Subject:[Asterisk-Users] help on mfc/r2

Melcon Moraes napisał(a):

> but can you make a simple call
> to your regular phone number from some SIP/IAX2 softphone/hardphone?

Right now? It's not working.
I could use (i have needed hardware).
Data: SIP/extension-number

Or even capi/zap channel.

When e400p is configured as a E1/PRI and connected to diffrent card, my 
".call"-file works (I hear asterisk-demo after receivng phone). So i 
assume my .call file is OK.

> What do you have in zaptel.conf file? For instance, I have this on my:
>
> span=1,1,0,cas,hdb3
> cas=1-15:1101
> cas=17-31:1101

Me too.
I've seen dchannel=16 somewhere on the net, but it makes me very 
confused, as R2 imvho is beeing "digigit-digit" on every litle 
"time-slot"/channel.

> hing
> to do with that. What happens if you use Unicall/g1 instead of just
> channel 1 of Unicall?

Same, it's still:

*CLI> -- Attempting call on Unicall/g1/363 for application 
playback(demo-thanks) (Retry 1)
Mar 27 01:42:00 NOTICE[13840]: channel.c:2437 __ast_request_and_dial: 
Unable to request channel Unicall/g1/363
Mar 27 01:42:00 NOTICE[13840]: pbx_spool.c:269 attempt_thread: Call 
failed to go through, reason 0

>
> Do you have zttool compiled? How those bits are showed up? The timing

│ Current Alarms: No alarms. │
│ Sync Source: Tormenta 2 (PCI) Quad E1 Card │
│ IRQ Misses: 0 │
│ Bipolar Viol: 609 │
│ Tx/Rx Levels: 0/ 0 │
│ Total/Conf/Act: 31/ 30/ 30 │
│ 1111111111222222222333 ┌──────┐ │
│ 1234567890123456789012345789012 │ Back │ │
│ TxA 111111111111111 111111111111111 └──────┘ │
│ TxB 111111111111111 111111111111111 │
│ TxC 000000000000000 000000000000000 │
│ TxD 111111111111111 111111111111111 │
│ ┌──────┐ │
│ RxA 000000000000000 000000000000000 │ Loop │ │
│ RxB 111111111111111 111111111111111 └──────┘ │
│ RxC 000000000000000 000000000000000 │
│ RxD 111111111111111 111111111111111 │
│ │

> source is correctly set up? Seems that your master timing sync source is
> the Alcatel, so you should use "span=1,1,0"
>
ok,



-- 
Krzysztof Drewicz
<drewicz at citicom.pl>
+48 22 34 54 363

E-mail classificado pelo Identificador de Spam Inteligente Terra.
Para alterar a categoria classificada, visite
http://mail.terra.com.br/protected_email/imail/imail.cgi?+_u=levelz&_l=1,1143420467.988851.6696.balcomo.terra.com.br,6575,Des15,Des15

 --Original Message Ends--

-- 
Melcon Moraes <melcon.moraes at terra.com.br>




More information about the asterisk-users mailing list